- 您現在的位置：買賣IC網 > PDF目錄9545 > MAX218CAP (Maxim Integrated Products)IC TXRX DUAL RS232 TRUE 20-SSOP PDF資料下載
參數資料
| 型號： | MAX218CAP |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX DUAL RS232 TRUE 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 66 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232 |
| 電源電壓： | 1.8 V ~ 4.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
MAX218
1.8V to 4.25V-Powered,
True RS-232 Dual Transceiver
_______________________________________________________________________________________
5
_______________Detailed Description
The MAX218 line driver/receiver is intended for battery-
powered EIA/TIA-232 and V.28/V.24 communications
interfaces that require two drivers and two receivers.
The operating voltage extends from 1.8V to 4.25V, yet
the device maintains true RS-232 and EIA/TIA-562
transmitter output voltage levels. This wide supply volt-
age range permits direct operation from a variety of
batteries without the need for a voltage regulator. For
example, the MAX218 can be run directly from a single
lithium cell or a pair of alkaline cells. It can also be run
directly from two NiCd or NiMH cells from full-charge
voltage down to the normal 0.9V/cell end-of-life point.
The 4.25V maximum supply voltage allows the two
rechargeable cells to be trickle- or fast-charged while
driving the MAX218.
The circuit comprises three sections: power supply,
transmitters, and receivers. The power-supply section
converts the supplied input voltage to 6.5V, providing the
voltages necessary for the drivers to meet true RS-232
levels. External components are small and inexpensive.
The transmitters and receivers are guaranteed to oper-
ate at 120kbps data rates, providing compatibility with
LapLink and other high-speed communications soft-
ware. A shutdown mode extends battery life by reduc-
ing supply current to 0.04A. While shut down, all
receivers can either remain active or be disabled under
logic control. With this feature, the MAX218 can be in
low-power shutdown mode and still monitor activity on
external devices. Three-state drivers are provided on
both receiver outputs.
Switch-Mode Power Supply
The switch-mode power supply uses a single inductor
with one diode and three small capacitors to generate
±6.5V from an input voltage in the 1.8V to 4.25V
range.
Inductor Selection
Use a 15H inductor with a saturation current rating of at
least 350mA and less than 1
resistance. Table 1 lists
suppliers of inductors that meet the 15H/350mA/1
specifications.
Diode Selection
Key diode specifications are fast recovery time (<10ns),
average current rating (>100mA), and peak current rat-
ing (>350mA). Inexpensive fast silicon diodes, such as
the 1N6050, are generally recommended. More expen-
sive Schottky diodes improve efficiency and give slightly
better performance at very low VCC voltages. Table 1
lists suppliers of both surface-mount and through-hole
diodes. 1N914s are usually satisfactory, but specifica-
tions and performance vary widely with different manu-
facturers.
Capacitor Selection
Use capacitors with values at least as indicated in
Figure 1. Capacitor C2 determines the ripple on V+,
but not the absolute voltage. Capacitors C1 and C3
determine both the ripple and the absolute voltage of
V-. Bypass VCC to GND with at least 1F (C4) placed
close to pins 5 and 6. If the VCC line is not bypassed
elsewhere (e.g., at the power supply), increase C4 to
4.7F.
You may use ceramic or polarized capacitors in all
locations. If you use polarized capacitors, tantalum
types are preferred because of the high operating fre-
quency of the power supplies (about 250kHz). If alu-
minum electrolytics are used, higher capacitance val-
ues may be required.
LapLink is a trademark of Traveling Software, Inc.
R1
R2
T1
T2
T1OUT
T2OUT
T1IN
T2IN
R1OUT
R2OUT
R1IN
R2IN
GND
EN
VCC
SHDN
LX
C1+
C1-
V-
6
3
7
8
9
10
11
12
13
14
16
18
15
4
5, 17, 20
MAX218
ENABLE
ON/OFF
1.8V
TO
4.25V
1
V+
19
1
F
C4
1
F
C2
1
F
C3
0.47
F
C1
15
H
D1
1N6050
Figure 1. Single-Supply Operation
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B1M-MY-S | CONVERTER MOD DC/DC 10V 50W |
| MS27474T12F35P | CONN RCPT 22POS JAM NUT W/PINS |
| MS3108A36-10P | CONN PLUG 48POS RT ANG W/PINS |
| MAX251CSD | IC DVR/RCVR DUAL RS232 5V 14SOIC |
| MS27468T21F75S | CONN RCPT 4POS JAM NUT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX218CAP+ | 功能描述:RS-232接口集成電路 1.8-4.25V True RS232 Dual Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX218CAP+T | 功能描述:RS-232接口集成電路 1.8-4.25V True RS232 Dual Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX218CAP-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX218CPP | 功能描述:RS-232接口集成電路 1.8-4.25V True RS232 Dual Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX218CPP+ | 功能描述:RS-232接口集成電路 1.8-4.25V True RS232 Dual Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。