- 您現在的位置：買賣IC網 > PDF目錄2157 > MAX2470EUT+T (Maxim Integrated Products)IC AMP VCO BUFFER DIFF SOT23-6 PDF資料下載
參數資料
| 型號： | MAX2470EUT+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP VCO BUFFER DIFF SOT23-6 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 放大器類型： | 緩沖器 |
| 電路數： | 1 |
| 輸出類型： | 差分 |
| 電流 - 輸入偏壓： | 10µA |
| 電流 - 電源： | 5.5mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-6 |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX2470EUT+TDKR |
_______________ Detailed Description
Bandwidth Control Circuitry
The MAX2470 features a logic-controlled bias circuit
which optimizes the performance for input frequencies
from 10MHz to 500MHz (HI/LO = VCC) and 10MHz to
200MHz (HI/LO = GND). Operating with HI/LO = GND
significantly reduces power consumption.
__________ Applications Information
Input Considerations
The MAX2470/MAX2471 offer high-impedance inputs,
ideal for low-distortion buffering of a VCO. For applica-
tions with discrete transistor-based oscillator designs,
simply AC-couple the oscillator directly to the inputs.
The buffer’s high input impedance results in minimal
loading on the oscillator. For still higher real input
impedance and reduced loading effects, match the
inputs with a shunt-L matching circuit followed by a
series blocking capacitor. For use with 50
VCO mod-
ules, terminate the buffer input(s) with a 50
shunt
resistor followed by a series-blocking capacitor. This
provides a very stable 50
termination and increases
reverse isolation. For those applications needing both
high gain and good input match, reactively match the
buffer inputs to 50
with simple two-element matching
circuits followed by a series blocking capacitor.
Output Considerations
The MAX2470 and MAX2471 incorporate fully differen-
tial output stages capable of driving an AC-coupled
100
differential load or two AC-coupled 50 single-
ended loads. This is ideal for applications that require
the oscillator to drive two application circuits (e.g. mixer
and PLL) simultaneously. The high output-to-output iso-
lation ensures minimal interaction between multiple
load circuits.
Layout and Power-Supply Bypassing
A properly designed PC board is essential to any RF/
microwave circuit. Be sure to use controlled impedance
lines on all high-frequency inputs and outputs. Bypass
the power supply with decoupling capacitors as close to
the VCC pins as possible. For long VCC lines (inductive), it
may be necessary to add additional decoupling capaci-
tors located further away from the device package.
Proper grounding of GND is essential. If the PC board
uses a topside RF ground, connect GND directly to it.
For a board where the ground plane is not on the com-
ponent side, the best technique is to connect GND to
the board with a plated through-hole (via) to the ground
plane close to the package.
MAX2470/MAX2471
10MHz to 500MHz VCO Buffer Amplifiers
with Differential Outputs
6
_______________________________________________________________________________________
Pin Description
Differential Noninverting Buffer Output. Broadband 50
output. AC coupling is required.
Do not DC couple to this pin.
OUT
1
PIN
1
MAX2471
MAX2470
NAME
2
RF Ground. Connect to the ground plane as close as possible to the IC to minimize
ground path inductance.
GND
2
3
—
Bias and Bandwidth Control Input. Connect to VCC to set internal bias for higher band-
width operation (10MHz to 500MHz). Connect to GND to set internal bias for lower band-
width operation (10MHz to 200MHz) and to reduce overall current consumption.
HI/LO
4
Differential Inverting Buffer Output. Broadband 50
output. AC coupling is required. Do
not DC couple to this pin.
OUT
3
4
Differential Inverting Buffer Input. High impedance input to buffer amplifier. See
Setting
The Input Impedance section.
IN
—
5
6
Supply Voltage Input. +2.7V < VCC < +5.5V.
VCC
6
Differential Noninverting Buffer Input. High impedance to buffer amplifier. See
Setting The
Input Impedance section.
IN
5
FUNCTION
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2472EUT+T | IC VCO BUFFER AMP SOT23-6 |
| MAX34406HETG+T | IC AMP CURR SENSE QUAD 24TQFN |
| MAX3798ETJ+T | IC LIMITING AMP/VCSEL DVR 32TQFN |
| MAX400CPA+ | IC OPAMP ULTRA LOW OFFSET 8-DIP |
| MAX4020EEE+ | IC OP AMP SNGL SPLY R-R 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2470EVKIT | 功能描述:放大器 IC 開發工具 MAX2470/71 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX24710EXG+ | 制造商:Microsemi Corporation 功能描述:MAX24710EXG+ - Bulk 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CLK SYNTHESIZER 10OUT 81CSBGA 制造商:Microsemi Corporation 功能描述:IC CLK SYNTHESIZER 10OUT 81CSBGA |
| MAX2471EUT | 功能描述:射頻放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2471EUT+ | 功能描述:射頻放大器 MAX2471EUT+ RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2471EUT+T | 功能描述:射頻放大器 10MHz - 500MHz VCO Buffer Amp RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。