- 您現在的位置：買賣IC網 > PDF目錄10637 > MAX3055ASD+ (Maxim Integrated Products)IC TXRX CAN FP 14-SOIC PDF資料下載
參數資料
| 型號： | MAX3055ASD+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/18頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX CAN FP 14-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1403 (CN2011-ZH PDF) |
Low-Power Modes
The transceiver provides three low-power modes that can
be entered or exited through pins STB and EN (Table 3).
Sleep Mode
The sleep mode is the mode with the lowest power con-
sumption. INH is switched to high impedance for deacti-
vation of the external voltage regulator. CANL is biased
to the battery voltage through RTL. If the supply voltage
is provided, RXD and ERR signal the wake-up interrupt.
Standby Mode
The standby mode reacts the same as the sleep mode,
but with a HIGH level on INH. Standby mode can be
used when the external voltage regulator needs to be
kept active during low-power operation.
Power-On Standby Mode
The power-on standby mode behaves similarly to the
standby mode with the battery power-on flag of the
wake-up interrupt signal on ERR. This mode is only for
reading the power-on flag. INH can be high or low in
the power-on standby mode. When the device goes
from standby mode to power-on standby mode, INH is
HIGH. When the device goes from sleep mode to
power-on standby mode, INH is low.
Wake-Up
Wake-up requests are recognized by the transceiver
when a dominant signal is detected on either bus line
or if WAKE detects a pulse for more than 38s. On a
wake-up request, INH is set high to activate an external
voltage regulator.
If VCC is provided, the wake-up request can be read on
the ERR or RXD outputs.
To prevent false wake-up due to transients or RF fields,
the wake-up voltage levels have to be maintained for more
than 38s. In the low-power modes, the failure detection
circuit remains partly active to prevent increased power
consumption in the event of failures 3, 4, 7, and 8.
Applications Information
The MAX3054/MAX3055/MAX3056 are capable of sus-
taining a network of up to 32 transceivers on a single
bus. The fault-tolerant transceivers are designed to
operate at a total termination resistance of 100
. Both
CANH and CANL lines are terminated with 100
. Since
the total termination resistance of the system is distrib-
uted over the entire bus, each of the transceivers con-
tributes only part of the total 100
termination. The
values of the termination resistors RTL and RTH vary
according to the size of the system and need to be cal-
culated. It is not required that each transceiver be ter-
minated with the same value, the total termination need
only be a total 100
.
The minimum termination resistor value allowed for
each transceiver is 500
, due to the driving capability
of RTH and RTL. This makes it impossible to achieve a
total termination resistance of 100
for systems smaller
than five transceivers. Typically this does not create a
problem because smaller systems usually have shorter
bus cables and have no problem with higher total ter-
mination resistance.
To reduce EMI in the case of an interrupted bus wire it
is recommended not to exceed 6k
termination resis-
tance at a single transceiver even though a higher
value is specified.
MAX3054/MAX3055/MAX3056
±80V Fault-Protected/Tolerant CAN
Transceivers for In-Car Applications
16
______________________________________________________________________________________
Note 1: In case the go-to-sleep command was used before.
Note 2: If the supply voltage VCC is present.
Note 3: Wake-up interrupts are released when entering the normal operating mode.
ERR
RXD
MODE
STB
EN
LOW
HIGH
LOW
HIGH
RTL
SWITCHED TO
Go-to-Sleep
Command
01
Sleep
0
0 (Note 1)
Standby
0
Wake-up
interrupt signal
(Notes 2 and 3)
—
Wake-up
interrupt signal
(Notes 2 and 3)
—
VBATT
Power-On
Standby
10
VBATT power-on
flag
—
Wake-up
interrupt signal
(Notes 2 and 3)
—
VBATT
Normal
Operating
1
Error flag
No error flag
Dominant
received data
Recessive
received data
VCC
Table 3. Low-Power Modes
相關PDF資料 |
PDF描述 |
|---|---|
| NCS2200SN2T1 | IC COMPARATOR 1V LOW PWR 5TSOP |
| MAX13053ASA+ | IC TRANSCEIVER CAN HS 8-SOIC |
| HR10A-7P-4P | 4 CONTACT PLUG W/PIN INSERT |
| MAX3054ASD+ | IC TXRX CAN FP 14-SOIC |
| MAX491EPD+ | IC TXRX RS485/RS422 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3055ASD+ | 功能描述:CAN 接口集成電路 80V Fault-Protected 2Mbps RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3055ASD+T | 功能描述:CAN 接口集成電路 80V Fault-Protected 2Mbps RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3055ASD-T | 功能描述:CAN 接口集成電路 80V Fault-Protected 2Mbps RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3056ASD | 功能描述:CAN 接口集成電路 80V Fault-Protected 2Mbps RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3056ASD+ | 功能描述:CAN 接口集成電路 80V Fault-Protected 2Mbps RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。