- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX3120EUA (Maxim Integrated Products)IC TXRX 3V IRDA IR 3V 8-UMAX PDF資料下載
參數資料
| 型號： | MAX3120EUA |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX 3V IRDA IR 3V 8-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | 紅外（IRDA） |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
MAX3120
Transmitter
The MAX3120’s IR transmitter consists of a high-power
MOS switch, capable of quickly switching 200mA with
less than 2
of on-resistance. Internal buffering keeps
the input capacitance of the TXD pin extremely low to
ease the input drive requirement. Connect an IR LED in
series with a current-setting resistor to select the appro-
priate IR output power (see the
Powering the IR LED
section). Note that the transmitter does not have an
automatic shutoff circuit, so pay special attention to com-
ponent power dissipation in high-duty-cycle transmit
schemes.
Applications Information
IR LED and PIN Photodiode Selection
The IrDA specification calls for an IR transmitter with a
peak wavelength between 850nm and 900nm. Within a
±15° half-cone-angle, the output intensity of the IR LED
must be between 40mW/sr and 500mW/sr. Outside a
±30° half-cone-angle, the output intensity of the IR LED
must fall below 40mW/sr. The optical rise and fall times
of the IR LED must be less than 600ns. Based on these
system requirements, the Hewlett Packard HSDL-4220
or the Temic TSHF5400 IR LEDs are two appropriate
choices.
Appropriate PIN photodiode selection is extremely
important to system performance. The PIN diode must
generate at least 200nA (minimum sensitivity of the
MAX3120) of current when aimed ±15° off-axis with an
incident irradiance of 4W/cm2. Use the following equa-
tion to determine if the Temic BPV22NF meets these
requirements:
The first term (4W/cm2) is the minimum guaranteed
irradiance in the ±15° angular range. The second term
(0.075cm2) is the effective sensitive area of the PIN
diode. The factor of 1.8 accounts for the efficiency
increase due to the spherical lens. The first 0.95 factor
normalizes the sensitivity to the 875nm wavelength,
while the second 0.95 factor adjusts for decreased
receiver efficiency at ±15° off-axis. The last term,
0.6A/W, is the sensitivity of the PIN diode. In this exam-
ple, the Temic BPV22NF is an appropriate selection.
The final important factor in selecting a PIN diode is
effective diode capacitance. It is important to keep this
capacitance below 70pF at 1.2V reverse bias. Higher
input capacitance can compromise system noise per-
formance by increasing the noise gain of the input tran-
simpedance amplifier.
Powering the IR LED
Set the current in the IR LED using an external resistor.
Consult the IR LED manufacturer’s data sheet to select
a forward current that will meet IrDA specifications dis-
cussed in the
IR LED and PIN Photodiode Selection
section. Look up the drop across the LED (VLED) and
the drop across the MAX3120 LED driver (see
Typical
Operating Characteristics - VLEDC) and choose the cur-
rent-setting resistor based on the following equation:
Using the Hewlett Packard HSDL-4220 IR LED as an
example, VCC = 5V, ISET = 100mA, and VLED = 1.67V,
therefore:
VLEDC = 0.08V
RSET = 32.5
R=
V- V
- V
I
SET
CC
LED
LEDC
SET
IPIN =
=
(4 W/cm )(0.075cm )(1.8)(0.95) (0.6A/W)
291nA
22
2
Low-Profile, 3V, 120A,
IrDA Infrared Transceiver
6
_______________________________________________________________________________________
Figure 1. Functional Diagram
MAX3120
BIAS
BANDPASS
FILTER
SHDN
VCC
RXD
TXD
LEDC
PGND
PINC
1.2V
+
-
GND
相關PDF資料 |
PDF描述 |
|---|---|
| MAX312ESE | IC SWITCH QUAD SPST 16SOIC |
| MAX312LEUE+ | IC SWITCH QUAD SPST 16TSSOP |
| MAX3131EAI | IC TXRX RS2332 IRDA IR 28-SSOP |
| MAX313FEPE+ | IC SWITCH QUAD SPST 16DIP |
| MAX3140EEI+ | IC UART W/RS485 28-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3120EUA+ | 功能描述:接口 - 專用 3V 120uA IrDA Infrared Tcvr RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX3120EUA+T | 功能描述:接口 - 專用 3V 120uA IrDA Infrared Tcvr RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX3120EUA-T | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX312C/D | 功能描述:模擬開關 IC 10Ohm Quad SPST CMOS Analog Switches RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX312CAE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。