- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX313FEPE+ (Maxim Integrated Products)IC SWITCH QUAD SPST 16DIP PDF資料下載
參數資料
| 型號： | MAX313FEPE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH QUAD SPST 16DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 25 |
| 功能： | 開關 |
| 電路： | 4 x SPST - NO |
| 導通狀態電阻： | 10 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 30 V，±4.5 V ~ 20 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
Detailed Description
The MAX312F/MAX313F/MAX314F are fault-protected
CMOS analog switches with unique operation and
construction. These switches differ considerably from
traditional fault-protection switches, with several advan-
tages. First, they are constructed with two parallel
FETs, allowing very low on-resistance when the switch
is on. Second, they allow signals on the NO_ or NC_
pins that are within, or slightly beyond, the supply rails
to be passed through the switch to the COM_ terminal
(or vice versa), allowing true rail-to-rail signal operation.
Third, the MAX312F/MAX313F/MAX314F have the same
fault-protection performance on any of the NO_, NC_,
or COM_ switch inputs. Operation is identical for both
fault polarities. The fault protection extends to ±36V
from GND with
±15V supplies.
During a fault condition, the particular overvoltage input
(COM_, NO_, NC_) pin becomes high impedance
regardless of the switch state or load resistance. When
power is removed, the fault protection is still in effect. In
this case, the COM_, NO_, or NC_ terminals are a virtu-
al open circuit. The fault can be up to ±40V with power
off. The switches turn off when V+ is not powered,
regardless of V-.
Pin Compatibility
These switches have identical pinouts to common non-
fault-protected CMOS switches. They allow for carefree
direct replacement in existing printed circuit boards
since the NO_, NC_, and COM_ pins of each switch are
fault protected.
Internal Construction
Internal construction is shown in Figure 1, with the ana-
log signal paths shown in bold. A single NO switch is
shown. The NC configuration is identical except the
logic-level translator becomes an inverter. The analog
switch is formed by the parallel combination of N-chan-
nel FET (N1) and P-channel FET (P1), which are driven
on and off simultaneously according to the input fault
condition and the logic-level state.
Normal Operation
Two comparators continuously compare the voltage on
the COM_, NO_, and NC_ pins with V+ and V-. When
the signal on COM_, NO_, or NC_ is between V+ and
V-, the switch acts normally, with FETs N1 and P1 turn-
ing on and off in response to IN_ signals. The parallel
combination of N1 and P1 forms a low-value resistor
between NO_ (or NC_) and COM_ so that signals pass
equally well in either direction.
Positive Fault Condition
When the signal on NO_ (or NC_) and COM_ exceeds
V+, the high-fault comparator output is high, turning off
FETs N1 and P1. This makes the NO_ (or NC_) and
COM_ pins high impedance regardless of the switch
MAX312F/MAX313F/MAX314F
Quad, Rail-to-Rail, Fault-Protected,
SPST Analog Switches
_______________________________________________________________________________________
9
PIN
MAX312F
MAX313F
MAX314F
NAME
FUNCTION
1, 16, 9, 8
IN1, IN2, IN3, IN4
Logic-Control Digital Inputs
2, 15, 10, 7
COM1, COM2, COM3,
COM4
Analog Switch Common Terminals
3, 14, 11, 6
——
NC1, NC2, NC3, NC4
Analog Switch Normally Closed Terminals
—
3, 14, 11, 6
—
NO1, NO2, NO3, NO4
Analog Switch Normally Open Terminals
——
3, 6
NO1, NO4
Analog Switch Normally Open Terminals
——
14, 11
NC2, NC3
Analog Switch Normally Closed Terminals
44
4
V-
Negative-Supply Voltage Input. Connect to GND for single-
supply operation. Bypass with a 0.1F capacitor to GND.
5
GND
Ground. Connect to digital ground.
12
N.C.
No Connection. Not internally connected.
13
V+
Positive-Supply Voltage Input. Bypass with a 0.1F capacitor
to GND.
Pin Description
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3140EEI+ | IC UART W/RS485 28-QSOP |
| MAX3157CAI | IC TXRX RS485/422 250KBPS 28SSOP |
| MAX3160CAP | IC TXRX RS485/422 10MBPS 20SSOP |
| MAX3160EEAP+T | IC TXRX RS232/485/422 20SSOP |
| MAX3170CAI | IC TXRX CLOCK/DATA 3.3V 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX313FEPE+ | 功能描述:模擬開關 IC 10Ohm Quad SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX313FESE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX313FESE+ | 功能描述:模擬開關 IC 10Ohm Quad SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX313FESE+T | 功能描述:模擬開關 IC 10Ohm Quad SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX313FESE-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。