- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX3175CAI+ (Maxim Integrated Products)IC TXRX MULTIPROTOCOL 28-SSOP PDF資料下載
參數資料
| 型號： | MAX3175CAI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX MULTIPROTOCOL 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 4/4 |
| 規程： | 多協議 |
| 電源電壓： | 5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
MXL1544/MAX3175
+5V Multiprotocol, Software-Selectable
Control Transceivers
______________________________________________________________________________________
11
The MXL1544/MAX3175s’ mode can be selected
through software control of the M0, M1, M2, INVERT,
and DCE/DTE inputs. Alternatively, the mode can be
selected by shorting the appropriate combination of
mode control inputs to GND (the inputs left floating will
be internally pulled up to VCC - logic HIGH). If the M0,
M1, and M2 mode inputs are all unconnected, the
MXL1544/MAX3175 will enter no-cable mode.
Fail-Safe
The MXL1544/MAX3175 guarantee a logic HIGH
receiver output when the receiver inputs are shorted or
open, or when they are connected to a terminated
transmission line with all drivers disabled. The V.11
receiver threshold is set between -200mV and 0mV to
guarantee fail-safe operation. If the differential receiver
input voltage (B - A) is
≥ 0mV, ROUT is logic HIGH. In
the case of a terminated bus with all transmitters dis-
abled, the receiver’s differential input voltage is pulled
to 0 by the termination. With the receiver thresholds of
the MXL1544/MAX3175, this results in ROUT logic
HIGH.
The V.10 receiver threshold is set between -250mV and
0mV. If the V.10 receiver input voltage is less than or
equal to -250mV, ROUT is logic HIGH. The V.28 receiv-
er threshold is set between 0.8V and 2.0V. If the receiv-
er input voltage is less than or equal to 0.8V, ROUT is
logic HIGH. In the case of a terminated bus with trans-
mitters disabled, the receiver’s input voltage is pulled
to 0 by the termination.
Applications Information
Cable-Selectable Mode
A cable-selectable, multiprotocol DTE/DCE interface is
shown in Figure 9. The mode control lines M0, M1, and
DCE/DTE are wired to the DB-25 connector. To select
the serial interface mode, the appropriate combination
of M0, M1, M2, and DCE/DTE are grounded within the
cable wiring. The control lines that are not grounded
are pulled high by the internal pullups on the MXL1543.
The serial interface protocol of the MXL1544/MAX3175
is now selected based on the cable that is connected
to the DB-25 interface.
V.10 (RS-423) Interface
The V.10 interface (Figure 10) is an unbalanced single-
ended interface capable of driving a 450
load. The
V.10 driver generates a minimum VO voltage of ±4V
across A’ and C’ when unloaded and a minimum volt-
age of 0.9 VO when loaded with 450
. The V.10
receiver has a single-ended input and does not reject
common-mode differences between C and C’. The V.10
receiver input trip threshold is defined between
+250mV and -250mV with input impedance character-
istic shown in Figure 11.
The MXL1544/MAX3175 V.10 mode receiver has a dif-
ferential threshold between -250mV and +250mV. To
ensure that the receiver has proper fail-safe operation
see the Fail-Safe section. To aid in rejecting system
noise, the MXL1544/MAX3175 V.10 receiver has a typi-
cal hysteresis of 25mV. Switch S3 in Figure 12 is open
in V.10 mode to disable the V.28 5k
termination at the
receiver input. Switch S4 is closed and switch S5 is
open to internally ground the receiver B input.
V.11 (RS-422) Interface
As shown in Figure 13, the V.11 protocol is a fully bal-
anced differential interface. The V.11 driver generates a
minimum of ±2V between nodes A and B when 100
minimum resistance is presented at the load. The V.11
receiver is sensitive to differential signals of ±200mV at
receiver inputs A’ and B’. The V.11 receiver input must
comply with the impedance curve of Figure 11 and
reject common-mode signals developed across the
cable (referenced from C to C’ in Figure 13) of up to
±7V.
The MXL1544/MAX3175 V.11 mode receiver has a dif-
ferential threshold between -200mV and +200mV. To
ensure that the receiver has proper fail-safe operation;
see the Fail-Safe section. To aid in rejecting system
noise, the MXL1544/MAX3175 V.11 receiver has a typi-
cal hysteresis of 15mV. Switch S3 in Figure 14 is open
in V.11 mode to disable the V.28 5k
termination at the
inverting receiver input. Because the control signals are
slow (60kbps), 100
termination resistance is generally
not required for the MXL1544/MAX3175. The receiver
inputs must also be compliant with the impedance
curve shown in Figure 11.
V.28 (RS-232) Interface
The V.28 interface is an unbalanced single-ended inter-
face (Figure 10). The V.28 generator provides a mini-
mum of ±5V across the 3k
load impedance between
A’ and C’. The V.28 receiver has single-ended input.
The MXL1544/MAX3175 V.28 mode receiver has a
threshold between +0.8V and +2.0V. To aid in rejecting
system noise, the MXL1544/MAX3175 V.28 receiver
has a typical hysteresis of 50mV. Switch S3 in Figure 15
is closed in V.28 mode to enable the 5k
V.28 termina-
tion at the receiver inputs.
No-Cable Mode
The MXL1544/MAX3175 will enter no-cable mode when
the mode-select pins are left unconnected or connect-
ed HIGH (M0 = M1 = M2 = 1). In this mode, the multi-
protocol drivers and receivers are disabled and the
相關PDF資料 |
PDF描述 |
|---|---|
| MAX31782ETL+T | IC MICROCONTROLLER 40TQFN |
| MAX3181EUK-T | IC RCVR RS232 1.5MBPS SOT23-5 |
| MAX3185CAP-T | IC TXRX RS232 230KPBS 20SSOP |
| MAX3186EWP | IC TXRX RS232 230KPBS 20-SOIC |
| MAX3187CAX+T | IC RS-232 SRL 230KBPS 36-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3175CAI+ | 功能描述:接口 - 專用 5V Multiprotocol RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX3175CAI+T | 功能描述:接口 - 專用 5V Multiprotocol RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX3175CAI-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX31760AEE+ | 功能描述:馬達/運動/點火控制器和驅動器 Fan Speed Controller w/LUT RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX31760AEE+T | 功能描述:馬達/運動/點火控制器和驅動器 Fan Speed Controller w/LUT RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。