- 您現在的位置：買賣IC網 > PDF目錄11330 > MAX322CSA+ (Maxim Integrated Products)IC SWITCH DUAL SPST 8SOIC PDF資料下載
參數資料
| 型號： | MAX322CSA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DUAL SPST 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 功能： | 開關 |
| 電路： | 2 x SPST - NC/NO |
| 導通狀態(tài)電阻： | 35 歐姆 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±3 V ~ 18 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
MAX320/MAX321/MAX322
Precision, Dual-Supply, SPST
Analog Switches
_______________________________________________________________________________________
5
__________Applications Information
Logic Levels
Calculate the logic thresholds typically as follows: VIH =
(V+ - 1.5V) and VIL = (V+ - 2.5V).
Power-supply consumption is minimized when IN1 and
IN2 are driven with logic-high levels equal to V+ and logic-
low levels well below the calculated VIL of (V+ - 2.5V). IN1
and IN2 can be driven to V- without damage.
Analog Signal Levels
Analog signals that range over the entire supply voltage
(V- to V+) can be switched, with very little change in on-
resistance over the entire voltage range (see
Typical
Operating Characteristics). All switches are bidirec-
tional, so NO_, NC_, and COM_ pins can be used as
either inputs or outputs.
Power-Supply Sequencing
and Overvoltage Protection
Do not exceed the absolute maximum ratings, because
stresses beyond the listed ratings may cause perma-
nent damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+, followed by V-,
before applying analog signals or logic inputs, especial-
ly if the analog or logic signals are not current-limited. If
this sequencing is not possible, and if the analog or
logic inputs are not current-limited to <30mA, add two
small signal diodes (D1, D2) as shown in Figure 1.
Adding protection diodes reduces the analog signal
range to a diode drop (about 0.7V) below V+ for D1,
and a diode drop above V- for D2. Leakage is not
affected by adding the diodes. On-resistance increas-
es by a small amount at low supply voltages. Maximum
supply voltage (V- to V+) must not exceed 17V.
Adding protection diode D1 causes the logic thresh-
olds to be shifted relative to the positive power-supply
rail. This can be significant when low positive supply
voltages (+5V or less) are used. Driving IN1 and IN2 all
the way to the supply rails (i.e., to a diode drop higher
than the V+ pin or a diode drop lower than the V- pin) is
always acceptable.
The protection diodes D1 and D2 also protect against
some overvoltage situations. With the circuit of Figure 1,
if the supply voltage is below the absolute maximum
rating and if a fault voltage up to the absolute maximum
rating is applied to an analog signal pin, no damage
will result. For example, with ±5V supplies, analog sig-
nals up to ±8.5V will not damage the circuit of Figure 1.
If only a single fault signal is present, the fault voltage
can rise to +12V or to -12V without damage.
_____________________Pin Description
POSITIVE SUPPLY
COM
D1
D2
NO
V-
Vg
V+
NEGATIVE SUPPLY
MAX320
MAX321
MAX322
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
5
Normally Closed Analog
Switch Terminal
NC2
(MAX321/MAX322)
Normally Open Analog
Switch Terminal
NO2
(MAX320)
Negative Supply
V-
4
Logic Inputs
IN2, IN1
3, 7
PIN
Analog Switch Common
Terminals
COM1, COM2
2, 6
Normally Closed Analog
Switch Terminal
NC1
(MAX321)
Normally Open Analog
Switch Terminal
NO1
(MAX320/MAX322)
1
FUNCTION
NAME
Positive Supply
V+
8
相關PDF資料 |
PDF描述 |
|---|---|
| DEHR33F331KB3B | CAP CER 330PF 3.15KV 10% RADIAL |
| ADG1401BCPZ-REEL7 | IC SWITCH SPST 1OHM RON 8LFCSP |
| DEHR33D391KN3A | CAP CER 390PF 2KV 10% RADIAL |
| DEHR33F181KD3B | CAP CER 180PF 3.15KV 10% RADIAL |
| PIC16F77T-I/L | IC MCU FLASH 8KX14 A/D 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX322CSA+ | 功能描述:模擬開關 IC Precision Dual Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX322CSA+T | 功能描述:模擬開關 IC Precision Dual Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX322CSA-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX322CUA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX322CUA+ | 功能描述:模擬開關 IC Precision Dual Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發(fā)布緊急采購，3分鐘左右您將得到回復。