參數資料
型號： MAX3301E
廠商： Maxim Integrated Products, Inc.
英文描述： CLAMP
中文描述： USB On-the-Go收發器與電荷泵
文件頁數： 27/33頁
文件大?。?/td> 935K
代理商： MAX3301E
M
USB On-the-Go Transceiver and Charge Pump
______________________________________________________________________________________
27
ID and Manufacturer Register Address Map
Table 16 provides the contents of the ID registers of the
MAX3301E. Addresses 00h and 01h comprise the ven-
dor ID registers. Addresses 02h and 03h comprise the
product ID registers. Addresses 14h and 15h comprise
the revision ID registers.
Audio Car Kit
Many cell phones are required to interface to car kits.
Depending upon the car kit, the interface to the phone
may be required to support any or all of the following
functions:
Audio input
Audio output
Charging
Control and status
The MAX3301E allows support of the CEA-936A car kit
interface standard.
External Components
External Resistors
Two external resistors (27.4
±1%) are required for
USB connection. Install one resistor in series between
D+ of the MAX3301E and D+ of the USB connector.
Install the other resistor in series between D- of the
MAX3301E and D- of the USB connector (see the
Typical Operating Circuit
).
External Capacitors
Five external capacitors are recommended for proper
operation. Install all capacitors as close to the device as
possible. Decouple V
L
to GND with a 0.1μF ceramic
capacitor. Bypass V
CC
to GND with a 1μF ceramic
capacitor. Bypass TRM to GND with a 1μF (or greater)
ceramic or plastic capacitor. Connect a 100nF flying
capacitor between C+ and C- for the charge pump (see
the
Typical Operating Circuit
). Bypass V
BUS
to GND
with a 1μF to 6.5μF ceramic capacitor in accordance
with USB OTG specifications.
ESD Protection
To protect the MAX3301E against ESD, D+, D-, ID_IN,
and V
BUS
have extra protection against static electricity
to protect the device up to ±15kV. The ESD structures
withstand high ESD in all states; normal operation, sus-
pend mode, interrupt shutdown, and shutdown. For the
ESD structures to work correctly, connect a 1μF or
greater capacitor from TRM to GND and from V
BUS
to
GND. ESD protection can be tested in various ways; the
D+, D-, ID_IN, and V
BUS
inputs/outputs are character-
ized for protection to the following limits:
±15kV using the Human Body Model
±6kV using the IEC 61000-4-2 Contact Discharge
Method
±10kV using the IEC 61000-4-2 Air-Gap Discharge
Method
REGISTER
ADDRESS
00h
01h
02h
03h
14h
15h
CONTENTS
6Ah
0Bh
01h
33h
77h
41h
Vendor ID
Product ID
Revision ID
Table 16. ID Registers
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
R
C
1M
R
D
1500
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 22. Human Body ESD Test Modes
I
P
100%
90%
36.8%
t
RL
TIME
t
DL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
0
AMPERES
Figure 23. Human Body Model Current Waveform
相關PDF資料
PDF描述
MAX3301EEBA-T CLAMP
MAX3301EETJ CLAMP
MAX333A Precision, Quad, SPDT, CMOS Analog Switch(MAX333的改進型,低導通電阻模擬開關)
MAX333 High Speed Quad SPST Analog Switches(接通電阻175Ω,漏電流5nA,導通速率1000ns，單刀單擲模擬開關)
MAX334EJE High Speed Quad SPST Analog Switch
相關代理商/技術參數
參數描述
MAX3301EEBA 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVER AND CHARG - Rail/Tube
MAX3301EEBA+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3301EEBA-T 功能描述:USB 接口集成電路 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
MAX3301EETI+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3301EETJ 功能描述:USB 接口集成電路 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*