- 您現在的位置：買賣IC網 > PDF目錄11564 > MAX3421EETJ+T (Maxim Integrated Products)IC USB PERIPH/HOST CNTRL 32TQFN PDF資料下載
參數資料
| 型號： | MAX3421EETJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB PERIPH/HOST CNTRL 32TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 控制器類型： | USB 外設控制器 |
| 接口： | USB/串行 |
| 電源電壓： | 3 V ~ 3.6 V |
| 電流 - 電源： | 15mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
| 配用： | MAX3421EVKIT-1+-ND - EVAL KIT FOR MAX3421E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
MAX3421E
USB Peripheral/Host Controller
with SPI Interface
5
Maxim Integrated
Pin Description
PIN
NAME
INPUT/
OUTPUT
FUNCTION
1
GPIN7
Input
General-Purpose Input. GPIN7–GPIN0 are connected to VL with internal pullup resistors.
GPIN7–GPIN0 logic levels are referenced to the voltage on VL.
2VL
Input
Level-Translator Voltage Input. Connect VL to the system’s 1.4V to 3.6V logic-level power
supply. Bypass VL to ground with a 0.1F capacitor as close to VL as possible.
3, 19
GND
Input
Ground
4
GPOUT0
5
GPOUT1
6
GPOUT2
7
GPOUT3
8
GPOUT4
9
GPOUT5
10
GPOUT6
11
GPOUT7
Output
General-Purpose Push-Pull Outputs. GPOUT7–GPOUT0 logic levels are referenced to the
voltage on VL.
12
RES
Input
Device Reset. Drive
RES low to clear all of the internal registers except for PINCTL (R17),
USBCTL (R15), and SPI logic. The logic level is referenced to the voltage on VL. (See the
Device Reset section for a description of resets available on the MAX3421E.) Note: The
MAX3421E is internally reset if either VCC or VL is not present. The register file is not accessible
under these conditions.
13
SCLK
Input
SPI Serial-Clock Input. An external SPI master supplies SCLK with frequencies up to 26MHz. The
logic level is referenced to the voltage on VL. Data is clocked into the SPI slave interface on the
rising edge of SCLK. Data is clocked out of the SPI slave interface on the falling edge of SCLK.
14
SS
Input
SPI Slave Select Input. The
SS logic level is referenced to the voltage on VL. When SS is driven
high, the SPI slave interface is not selected, the MISO pin is high impedance, and SCLK
transitions are ignored. An SPI transfer begins with a high-to-low
SS transition and ends with a
low-to-high
SS transition.
15
MISO
Output
SPI Serial-Data Output (Master-In Slave-Out). MISO is a push-pull output. MISO is tri-stated in
half-duplex mode or when
SS = 1. The MISO logic level is referenced to the voltage on VL.
16
MOSI
Input or
Input/
Output
SPI Serial-Data Input (Master-Out Slave-In). The logic level on MOSI is referenced to the
voltage on VL. MOSI can also be configured as a bidirectional MOSI/MISO input and output.
(See Figure 15.)
17
GPX
Output
General-Purpose Multiplexed Push-Pull Output. The internal MAX3421E signal that appears on
GPX is programmable by writing to the GPXB and GPXA bits of the PINCTL (R17) register and the
SEPIRQ bit of the MODE (R27) register. GPX indicates one of five signals (see the GPX section).
18
INT
Output
Interrupt Output. In edge mode, the logic level on INT is referenced to the voltage on VL and is
a push-pull output with programmable polarity. In level mode, INT is open-drain and active low.
Set the IE bit in the CPUCTL (R16) register to enable INT.
20
D-
Input/
Output
USB D- Signal. Connect D- to a USB connector through a 33
Ω ±1% series resistor. A
switchable 15k
Ω D- pulldown resistor is internal to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| V375C28M75B3 | CONVERTER MOD DC/DC 28V 75W |
| MAX5942BESE+ | IC IEEE 802.3AF POE SYSTM 16SOIC |
| 78Q8430-100IGTR/F | IC LAN MEDIA ACCESS CTLR 100LQFP |
| GRM2165C1H510JZ01D | CAP CER 51PF 50V 5% NP0 0805 |
| MAX5942BCSE+ | IC IEEE 802.3AF POE SYSTM 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3421EVKIT-1+ | 功能描述:界面開發工具 MAX3421E/20E Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX3430CPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3430CPA+ | 功能描述:RS-485接口IC Fail-Safe 1/4-Unit 3.3V Transceiver RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3430CSA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3430CSA+ | 功能描述:RS-485接口IC Fail-Safe 1/4-Unit 3.3V Transceiver RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。