- 您現在的位置：買賣IC網 > PDF目錄5815 > MAX34406HETG+ (Maxim Integrated Products)IC AMP CURR SENSE QUAD 24TQFN PDF資料下載
參數資料
| 型號： | MAX34406HETG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURR SENSE QUAD 24TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 放大器類型： | 電流檢測 |
| 電路數： | 4 |
| 輸出類型： | 開路漏極 |
| -3db帶寬： | 30kHz |
| 電流 - 輸入偏壓： | 200nA |
| 電壓 - 輸入偏移： | 100µV |
| 電流 - 電源： | 200µA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-TQFN-EP（4x4） |
| 包裝： | 管件 |
Maxim Integrated Products 8
MAX34406
Quad Current-Sense Amplifier
with Overcurrent Threshold Comparators
Detailed Description
The MAX34406 quad-channel, unidirectional, high-side,
current-sense amplifier features a 2.0V to 28V input
common-mode range. This feature allows the monitoring
of current out of a voltage supply as low as 2.0V. The
device monitors current through a current-sense resistor
and amplifies the voltage across that resistor.
Current-sense amplifier output voltages (OUT1 to OUT4)
are compared to a fixed 1.0V reference; if VOUTx
exceeds 1.0V, the corresponding overcurrent warning
output (OC1 to OC4) is asserted. If the enable input
(ENA) is logic-high, SHTDN asserts when any of the four
overcurrent outputs go logic-high. Assertion of SHTDN on
overcurrent can be delayed and/or filtered by attaching
an external capacitor to CDLY. Once SHTDN is latched
high impedance, it remains so until ENA is toggled.
The unidirectional current-sense amplifiers used in each
channel of the device have a well established history. For
each channel, an op amp is used to force the current
through an internal gain resistor at IN+, which has a value
of R1, such that its voltage drop equals the voltage drop
across an external sense resistor, RSENSE. There is an
internal resistor at IN- with the same value as R1 to mini-
mize offset voltage. The current through R1 is sourced by
a high-voltage p-channel FET. Its source current is the
same as its drain current, which flows through a second
gain resistor, ROUTx. This produces an output voltage,
VOUTx, whose magnitude is ILOAD x RSENSE x ROUTx/R1.
The gain accuracy is based on the matching of the two
gain resistors, R1 and ROUTx (Table 1). Total gain = 25V/V
for the MAX34406T, 50V/V for the MAX34406F, 100V/V
for the MAX34406H, and 200V/V for the MAX34406W.
The output is protected from input overdrive by use of a
6V clamp-protection circuit.
Applications Information
Choosing the Sense Resistor
Choose RSENSE based on the criteria detailed in the fol-
lowing sections.
Voltage Loss
A high RSENSE value causes the power-source voltage
to drop due to IR loss. For minimal voltage loss, use the
lowest RSENSE value.
OUTx Swing vs. VINx+ and VSENSE
The device is unique because the supply voltage for
the current-sense amplifier in each channel is the input
common-mode voltage for that channel (the average
voltage at INx+ and INx-). There are no separate supply
voltage pins for the current-sense amplifiers. Therefore,
the OUTx voltage swing for a given channel is limited by
the minimum voltage at IN+ for that channel.
VOUTx(MAX) = VINx+(MIN) - VSENSE(MAX) - VOH
and
OUTx
SENSE
LOAD
V
(MAX)
R
G I
(MAX)
=
×
VSENSE full scale should be less than VOUTx/gain at the
minimum INx+ voltage. For best performance with a 3.6V
supply voltage, select RSENSE to provide approximately
120mV (gain of 25V/V), 60mV (gain of 50V/V), 30mV (gain
of 100V/V), or 15mV (gain of 200V/V) of sense voltage for
the full-scale current in each application. These can be
increased by use of a higher minimum input voltage.
Accuracy
In the linear region (VOUTx < VOUTx(MAX)), there are
two components to accuracy: input offset voltage (VOS)
and gain error (GE). For all variants of the device,
VOS = P 600FV (max); gain error is 0.6% (max) for the
MAX34406T/F/H or 0.8% (max) for the MAX34406W. Use
the linear equation to calculate total error:
OS
SENSE
V
Error (%) GE
100
V
=
±×
where GE is gain error, VSENSE is the voltage across
the sense resistor RSENSE, and VOS is offset voltage. A
high RSENSE value allows lower currents to be measured
more accurately because offsets are less significant
when the sense voltage is larger.
Table 1. Internal Gain Setting Resistors
(Typical Values)
GAIN (V/V)
R1 (I)
ROUTx (kI)
200
100
20
100
10
50
200
10
25
400
10
相關PDF資料 |
PDF描述 |
|---|---|
| BK1/S506-1.25-R | FUSE 1.25A 250V TLAG 5X20 IEC |
| MAX4198ESA+ | IC AMP DIFF PREC R-R 8-SOIC |
| MAX4198EUA+ | IC AMP DIFF PREC R-R 8-UMAX |
| AD8045ACPZ-REEL7 | IC OPAMP VF ULDIST LN 8LFCSP |
| 1.5KE10CAHE3/54 | TVS BIDIR 1.5KW 10V 5% 1.5KE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX34406HETG+ | 功能描述:特殊用途放大器 Quad Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MAX34406HETG+T | 功能描述:特殊用途放大器 Quad Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MAX34406HETG+TW | 制造商:Maxim Integrated Products 功能描述:WAIVER PART FOR QUAD CURRENT SENSE FAULT DETECTOR T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC AMP CURRENT SENSE 24-TQFN 制造商:Maxim Integrated Products 功能描述:Quad Current-Sense Amplifier |
| MAX34406TETG+ | 功能描述:電流靈敏放大器 QUAD CURRENT-SENSE MONITOR 24L 25V RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX34406TETG+T | 制造商:Maxim Integrated Products 功能描述:QUAD CURRENT SENSE MONITOR 24L 25V TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:QUAD CURRENT SENSE MONITOR 24L 25V - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC OPAMP CURR SENSE 60KHZ 24TQFN |
發布緊急采購，3分鐘左右您將得到回復。