參數資料
型號: MAX4017ESA+
廠商: Maxim Integrated Products
文件頁數: 11/12頁
文件大?。?/td> 0K
描述: IC BUFFER R-R 8-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 100
放大器類型: 緩沖器
電路數: 2
輸出類型: 滿擺幅
轉換速率: 600 V/µs
-3db帶寬: 200MHz
電流 - 輸入偏壓: 5.4µA
電壓 - 輸入偏移: 4000µV
電流 - 電源: 5.5mA
電流 - 輸出 / 通道: 120mA
電壓 - 電源,單路/雙路(±): 3.15 V ~ 11 V,±1.575 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOIC
包裝: 管件
產品目錄頁面: 1423 (CN2011-ZH PDF)
MAX4014/MAX4017/MAX4019/MAX4022
Low-Cost, High-Speed, Single-Supply, Gain of +2
Buffers with Rail-to-Rail Outputs in SOT23
8
_______________________________________________________________________________________
_______________Detailed Description
The MAX4014/MAX4017/MAX4019/MAX4022 are sin-
gle-supply, rail-to-rail output, voltage-feedback, closed-
loop buffers that employ current-feedback techniques
to achieve 600V/s slew rates and 200MHz band-
widths. These buffers use internal 500
resistors to
provide a preset closed-loop gain of +2V/V in the non-
inverting configuration or -1V/V in the inverting configu-
ration. Excellent harmonic distortion and differential
gain/phase performance make these buffers an ideal
choice for a wide variety of video and RF signal-pro-
cessing applications.
Local feedback around the buffer’ s output stage
ensures low output impedance, which reduces gain
sensitivity to load variations. This feedback also pro-
duces demand-driven current bias to the output tran-
sistors for ±120mA drive capability, while constraining
total supply current to less than 7mA.
__________Applications Information
Power Supplies
These devices operate from a single +3.15V to +11V
power supply or from dual supplies of ±1.575V to
±5.5V. For single-supply operation, bypass the VCC pin
to ground with a 0.1F capacitor as close to the pin as
possible. If operating with dual supplies, bypass each
supply with a 0.1F capacitor.
Selecting Gain Configuration
Each buffer in the MAX4014 family can be configured
for a voltage gain of +2V/V or -1V/V. For a gain of
+2V/V, ground the inverting terminal. Use the noninvert-
ing terminal as the signal input of the buffer (Figure 1a).
Grounding the noninverting terminal and using the
inverting terminal as the signal input configures the
buffer for a gain of -1V/V (Figure 1b).
Since the inverting input exhibits a 500
input imped-
ance, terminate the input with a 56
resistor when the
device is configured for an inverting gain in 50
appli-
cations (terminate with 88
in 75 applications).
Terminate the input with a 49.9
resistor in the nonin-
verting case. Output terminating resistors should direct-
ly match cable impedances in either configuration.
Layout Techniques
Maxim recommends using microstrip and stripline tech-
niques to obtain full bandwidth. To ensure that the PC
board does not degrade the buffer’s performance, design
it for a frequency greater than 1GHz. Pay careful attention
to inputs and outputs to avoid large parasitic capaci-
tance. Whether or not you use a constant-impedance
board, observe the following guidelines when designing
the board:
Don’t use wire-wrapped boards. They are too inductive.
Don’t use IC sockets. They increase parasitic capac-
itance and inductance.
Use surface-mount instead of through-hole compon-
ents for better high-frequency performance.
Use a PC board with at least two layers; it should be
as free from voids as possible.
Keep signal lines as short and as straight as possi-
ble. Do not make 90° turns; round all corners.
MAX40_ _
500
500
IN-
OUT
*R
OUT
IN
RTIN
IN+
*RL = 2R
MAX40_ _
500
500
OUT
*R
OUT
RS
RTIN
IN+
IN-
IN
*RL = 2R
Figure 1a. Noninverting Gain Configuration (AV = +2V/V)
Figure 1b. Inverting Gain Configuration (AV = -1V/V)
相關PDF資料
PDF描述
MAX4163EUA+ IC OP AMP R-R I/O SS 8-UMAX
RMCF0805FT330R RES 330 OHM 1/8W 1% 0805 SMD
AD706JR-REEL IC OPAMP GP DUAL PREC 15MA 8SOIC
MAX4168EUB+ IC OP AMP R-R I/O W/SD 10-UMAX
LTC6079CGN#TRPBF IC OP AMP QUAD R-R I/O 16SSOP
相關代理商/技術參數
參數描述
MAX4017ESA+ 功能描述:高速運算放大器 High-Speed Single Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4017ESA+T 功能描述:高速運算放大器 High-Speed Single Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4017ESA-T 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4017EUA 功能描述:高速運算放大器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4017EUA+ 功能描述:高速運算放大器 High-Speed Single Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube