- 您現在的位置：買賣IC網 > PDF目錄3507 > MAX4019ESD+ (Maxim Integrated Products)IC BUFFER R-R 14SOIC PDF資料下載
參數資料
| 型號： | MAX4019ESD+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BUFFER R-R 14SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 放大器類型： | 緩沖器 |
| 電路數： | 3 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 600 V/µs |
| -3db帶寬： | 200MHz |
| 電流 - 輸入偏壓： | 5.4µA |
| 電壓 - 輸入偏移： | 4000µV |
| 電流 - 電源： | 5.5mA |
| 電流 - 輸出 / 通道： | 120mA |
| 電壓 - 電源，單路/雙路(±)： | 3.15 V ~ 11 V，±1.575 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1387 (CN2011-ZH PDF) |
MAX4014/MAX4017/MAX4019/MAX4022
Low-Cost, High-Speed, Single-Supply, Gain of +2
Buffers with Rail-to-Rail Outputs in SOT23
8
_______________________________________________________________________________________
_______________Detailed Description
The MAX4014/MAX4017/MAX4019/MAX4022 are sin-
gle-supply, rail-to-rail output, voltage-feedback, closed-
loop buffers that employ current-feedback techniques
to achieve 600V/s slew rates and 200MHz band-
widths. These buffers use internal 500
resistors to
provide a preset closed-loop gain of +2V/V in the non-
inverting configuration or -1V/V in the inverting configu-
ration. Excellent harmonic distortion and differential
gain/phase performance make these buffers an ideal
choice for a wide variety of video and RF signal-pro-
cessing applications.
Local feedback around the buffer’ s output stage
ensures low output impedance, which reduces gain
sensitivity to load variations. This feedback also pro-
duces demand-driven current bias to the output tran-
sistors for ±120mA drive capability, while constraining
total supply current to less than 7mA.
__________Applications Information
Power Supplies
These devices operate from a single +3.15V to +11V
power supply or from dual supplies of ±1.575V to
±5.5V. For single-supply operation, bypass the VCC pin
to ground with a 0.1F capacitor as close to the pin as
possible. If operating with dual supplies, bypass each
supply with a 0.1F capacitor.
Selecting Gain Configuration
Each buffer in the MAX4014 family can be configured
for a voltage gain of +2V/V or -1V/V. For a gain of
+2V/V, ground the inverting terminal. Use the noninvert-
ing terminal as the signal input of the buffer (Figure 1a).
Grounding the noninverting terminal and using the
inverting terminal as the signal input configures the
buffer for a gain of -1V/V (Figure 1b).
Since the inverting input exhibits a 500
input imped-
ance, terminate the input with a 56
resistor when the
device is configured for an inverting gain in 50
appli-
cations (terminate with 88
in 75 applications).
Terminate the input with a 49.9
resistor in the nonin-
verting case. Output terminating resistors should direct-
ly match cable impedances in either configuration.
Layout Techniques
Maxim recommends using microstrip and stripline tech-
niques to obtain full bandwidth. To ensure that the PC
board does not degrade the buffer’s performance, design
it for a frequency greater than 1GHz. Pay careful attention
to inputs and outputs to avoid large parasitic capaci-
tance. Whether or not you use a constant-impedance
board, observe the following guidelines when designing
the board:
Don’t use wire-wrapped boards. They are too inductive.
Don’t use IC sockets. They increase parasitic capac-
itance and inductance.
Use surface-mount instead of through-hole compon-
ents for better high-frequency performance.
Use a PC board with at least two layers; it should be
as free from voids as possible.
Keep signal lines as short and as straight as possi-
ble. Do not make 90° turns; round all corners.
MAX40_ _
500
500
IN-
OUT
*R
OUT
IN
RTIN
IN+
*RL = 2R
MAX40_ _
500
500
OUT
*R
OUT
RS
RTIN
IN+
IN-
IN
*RL = 2R
Figure 1a. Noninverting Gain Configuration (AV = +2V/V)
Figure 1b. Inverting Gain Configuration (AV = -1V/V)
相關PDF資料 |
PDF描述 |
|---|---|
| MMS-110-02-T-SH | CONN RCPT 2MM 10POS SGL HORZ SMD |
| TSW-143-08-T-D-RA | CONN HEADER 86PS .100 DL R/A TIN |
| MAX4022EEE+ | IC BUFFER R-R 16-QSOP |
| PEC33DBBN | CONN HEADER .100 DUAL R/A 66POS |
| MAX4216EUA+ | IC OP AMP R-R W/ENABLE 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4019ESD+ | 功能描述:高速運算放大器 High-Speed Single Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4019ESD+T | 功能描述:高速運算放大器 High-Speed Single Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4019ESD-T | 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4020 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Cost, High-Speed, SOT23, Single-Supply Op Amps with Rail-to-Rail Outputs |
| MAX40-20.0C | 制造商:MDE 制造商全稱:MDE Semiconductor, Inc. 功能描述:HIGH CURRENT TRANSIENT VOLTAGE SUPPRESSOR (TVS) DIODE |
發布緊急采購，3分鐘左右您將得到回復。