- 您現在的位置：買賣IC網 > PDF目錄2157 > MAX4207ETE+ (Maxim Integrated Products)IC AMP TRANS LOG 16-TQFN PDF資料下載
參數資料
| 型號： | MAX4207ETE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/15頁 |
| 文件大小： | 0K |
| 描述： | IC AMP TRANS LOG 16-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 放大器類型： | 對數 |
| 電路數： | 1 |
| 轉換速率： | 12 V/µs |
| 增益帶寬積： | 5MHz |
| -3db帶寬： | 1MHz |
| 電流 - 輸入偏壓： | 10pA |
| 電壓 - 輸入偏移： | 600µV |
| 電流 - 電源： | 5mA |
| 電流 - 輸出 / 通道： | 58mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN-EP（4x4） |
| 包裝： | 管件 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
MAX4207
Precision Transimpedance Logarithmic
Amplifier with Over 5 Decades of Dynamic Range
12
______________________________________________________________________________________
Output Offset
The inverting configuration utilized by the MAX4207
facilitates large output-offset voltage adjustments. The
magnitude of the offset voltage is given by the following
equation:
A resistive divider between REFVOUT, OSADJ, and
GND can be used to adjust VOSADJ (see Figure 5).
Scale Factor
The scale factor, K, is the slope of the logarithmic output.
For the LOGV1 amplifier, K = -0.25V/decade. Adjust the
overall scale factor for the MAX4207 using the uncom-
mitted LOGV2 amplifier and the following equation,
which refers to Figure 5:
Select R2 between 1k and 100k.
Design Example
Desired:
Logarithmic intercept: 1A
Overall scale factor = +1V/decade
Select R1 = 10k:
Photodiode Current Monitoring
Figure 6 shows the MAX4207 in an optical-power
measurement circuit, common in fiberoptic applications.
The MAX4007 current monitor converts the sensed APD
current to an output current that drives the MAX4207
LOGIIN input (APD current is scaled by 0.1). The
MAX4007 also buffers the high-voltage APD voltages
from the lower MAX4207 voltages. The MAX4207’s inter-
nal current reference sources 10nA (RSET = 5M) to the
REFIIN input. This configuration sets the logarithmic inter-
cept to 10nA, corresponding to an APD current of 100nA.
The unity-gain configuration of the output buffer maintains
the -0.25V/decade gain present at the LOGV1 output.
Measuring Optical Absorbance
A photodiode provides a convenient means of measur-
ing optical power, as diode current is proportional to
the incident optical power. Measure absolute optical
power using a single photodiode connected at LOGIIN,
with the MAX4207’s internal current reference driving
REFIIN. Alternatively, connect a photodiode to each of
the MAX4207’s logging inputs, LOGIIN and REFIIN, to
measure relative optical power (Figure 7).
In absorbance measurement instrumentation, a refer-
ence light source is split into two paths. The unfiltered
path is incident upon the photodiode of the reference
channel, REFIIN. The other path passes through a sam-
ple of interest, with the resulting filtered light incident on
the photodiode of the second channel, LOGIIN. The
MAX4207 outputs provide voltages proportional to the
log ratio of the two optical powers—an indicator of the
optical absorbance of the sample.
In wavelength-locking applications, often found in
fiberoptic communication modules, two photodiode cur-
rents provide a means of determining whether a given
optical channel is tuned to the desired optical frequen-
cy. In this application, two bandpass optical filters with
overlapping “skirts” precede each photodiode. With
proper filter selection, the MAX4207 output can vary
monotonically (ideally linearly) with optical frequency.
Rk
V decade
k
210
1
025
40
=×
=
/
.
R
V
A
k
SET =
×
=
05
10 1
50
.
RR
K
21
025
=
.
VV
R
RR
OSADJ
REFOUT
=
+
4
34
VV
R
OS
OSADJ
=+
1
2
1
Table 1. MAX4207 Example Configurations
LOGV2 AMPLIFIER CONFIGURATION
INPUT CONDITIONS
VLOGV1
VLOGV2
ILOG > IREF (constant)
Negative
Positive
Inverting
ILOG < IREF (constant)
Positive
Negative
ILOG > IREF (constant)
Negative
Noninverting
ILOG < IREF (constant)
Positive
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4208AUA+T | IC INSTRUMENT AMP PREC 8-UMAX |
| MAX420CPA+ | IC OPAMP CMOS CHOPPER-STAB 8-DIP |
| MAX4217EUA+ | IC BUFFER R-R W/ENABLE 8-UMAX |
| MAX4218EEE+T | IC OP AMP R-R W/ENABLE 16QSOP |
| MAX4228ESD+ | IC AMP CURRENT FB LP 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4207ETE+ | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4207ETE+T | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4207ETE-T | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4208AUA+ | 功能描述:儀表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MAX4208AUA+T | 功能描述:儀表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。