- 您現在的位置：買賣IC網 > PDF目錄5814 > MAX4209HAUA+ (Maxim Integrated Products)IC INSTRUMENT AMP PREC 8-UMAX PDF資料下載
參數資料
| 型號： | MAX4209HAUA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INSTRUMENT AMP PREC 8-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.055 V/µs |
| -3db帶寬： | 7.5kHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 3µV |
| 電流 - 電源： | 1.4mA |
| 電流 - 輸出 / 通道： | 25mA |
| 電壓 - 電源，單路/雙路(±)： | 2.85 V ~ 5.5 V，±1.425 V ~ 2.25 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 產品目錄頁面： | 1388 (CN2011-ZH PDF) |
MAX4208/MAX4209
Ultra-Low Offset/Drift, Precision
Instrumentation Amplifiers with REF Buffer
14
______________________________________________________________________________________
Power-Supply Bypass and Layout
Good layout technique optimizes performance by
decreasing the amount of stray capacitance at the
instrumentation amplifier’s gain-setting pins (OUT, FB,
and REF). Excess capacitance produces peaking in
the amplifier’s frequency response. To decrease stray
capacitance, minimize trace lengths by placing exter-
nal components as close as possible to the instrumen-
tation amplifier. Unshielded long traces at the inputs of
the instrumentation amplifier degrade the CMRR and
pick-up noise. This produces inaccurate output in high-
gain configurations. Use shielded or coax cables to
connect the inputs of the instrumentation amplifier.
Since the MAX4208/MAX4209 feature ultra-low input
offset voltage, board leakage and thermocouple effects
can easily introduce errors in the input offset voltage
readings when used with high-impedance signal
sources. Minimize board leakage current and thermo-
couple effects by thoroughly cleaning the board and
placing the matching components very close to each
other and with appropriate orientation. For best perfor-
mance, bypass each power supply to ground with a
separate 0.1F capacitor.
For noisy digital environments, the use of multilayer
PCB with separate ground and power-supply planes is
recommended. Keep digital signals far away from the
sensitive analog inputs.
Refer to the MAX4208 or MAX4209 Evaluation Kit data
sheets for good layout examples.
Low-Side Current-Sense Amplifier
The use of indirect current-feedback architecture
makes the MAX4208/MAX4209 ideal for low-side cur-
rent-sensing applications, i.e., where the current in the
circuit ground needs to be measured by means of a
small sense resistor. In these situations, the input com-
mon-mode voltage is allowed to be at or even slightly
below ground (VSS - 0.1V).
If the currents to be measured are bidirectional, con-
nect REFIN/MODE to VDD/2 to get full dynamic range
for each direction. If the currents to be measured are
unidirectional, both REFIN/MODE and REF can be tied
to GND. However, VOL limitations can limit low-current
measurement. If currents need to be measured down to
0A, bias REFIN/MODE to a voltage above 0.2V to acti-
vate the internal buffer and to stay above amplifier VOL,
and measure both OUT and REF with a differential
input ADC.
Low-Voltage, High-Side
Current-Sense Amplifier
Power management is a critical area in high-perfor-
mance portable devices such as notebook computers.
Modern digital processors and ASICs are using smaller
transistor geometries to increase speed, reduce size,
and also lower their operating core voltages (typically
0.9V to 1.25V). The MAX4208/MAX4209 instrumentation
amplifiers can be used as a nearly zero voltage-drop,
current-sense amplifier (see Figure 5).
VCM
VCC
VCM-MAX
3/4 VCC
1/2 VCC
1/4 VCC
0
VCC/2
VCC
VOUT
( = GAIN x VDIFF + VREF)
VREF = 1/2 VCC
CLASSIC THREE OP-AMP INA
VCM
VDD
VCM-MAX
0
VDD/2
VDD
VOUT
( = GAIN x VDIFF + VREF)
VREF = 1/2 VDD
MAX4208/MAX4209
Figure 3. Limited Common Mode vs. Output Voltage of a
Three Op-Amp INA
Figure 4. Input Common Mode vs. Output Voltage of
MAX4208/MAX4209 Includes 0V (GND)
相關PDF資料 |
PDF描述 |
|---|---|
| 151210-2420-RB | CONN HEADR 2MM 10POS DL SMD GOLD |
| 2095-450-BLF | SURGE ARRESTOR GDT 4500V AXIAL |
| TSW-110-09-T-S | CONN HEADER 10POS .100" SNGL |
| MAX4017EUA+ | IC BUFFER R-R 8-UMAX |
| TSW-206-08-T-S-RA | CONN HEADER 6POS .200" R/A TIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4209HAUA+ | 功能描述:儀表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MAX4209HAUA+T | 功能描述:儀表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MAX420C/D | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX420CPA | 功能描述:運算放大器 - 運放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX420CPA+ | 功能描述:運算放大器 - 運放 Chopper Stabilized RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。