- 您現在的位置：買賣IC網 > PDF目錄5511 > MAX4219ESD+T (Maxim Integrated Products)IC OP AMP R-R W/ENABLE 14SOIC PDF資料下載
參數資料
| 型號： | MAX4219ESD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/16頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R W/ENABLE 14SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 緩沖器 |
| 電路數： | 3 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 600 V/µs |
| -3db帶寬： | 200MHz |
| 電流 - 輸入偏壓： | 5.4µA |
| 電壓 - 輸入偏移： | 4000µV |
| 電流 - 電源： | 5.5mA |
| 電流 - 輸出 / 通道： | 120mA |
| 電壓 - 電源，單路/雙路(±)： | 3.15 V ~ 11 V，±1.575 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
________________ Detailed Description
The MAX4214/MAX4215/MAX4217/MAX4219/MAX4222
are single-supply, rail-to-rail output, voltage-feedback,
closed-loop buffers that employ current-feedback tech-
niques to achieve 600V/s slew rates and 230MHz
bandwidths. These buffers use internal 500
resistors
to provide a preset closed-loop gain of 2V/V in the non-
inverting configuration or -1V/V in the inverting configu-
ration. Excellent harmonic distortion and differential
gain/phase performance make them an ideal choice for
a wide variety of video and RF signal-processing appli-
cations.
Local feedback around the buffer’s output stage
ensures low output impedance, which reduces gain
sensitivity to load variations. This feedback also pro-
duces demand-driven current bias to the output tran-
sistors for ±120mA drive capability, while constraining
total supply current to less than 7mA.
___________Applications Information
Power Supplies
These devices operate from a single 3.15V to 11V
power supply or from dual supplies of ±1.575V to
±5.5V. For single-supply operation, bypass the VCC pin
to ground with a 0.1F capacitor as close to the pin as
possible. If operating with dual supplies, bypass each
supply with a 0.1F capacitor.
Selecting Gain Configuration
Each buffer in the MAX4214 family can be configured
for a voltage gain of 2V/V or -1V/V. For a gain of 2V/V,
ground the inverting terminal. Use the noninverting ter-
minal as the signal input of the buffer (Figure 1a).
Grounding the noninverting terminal and using the
inverting terminal as the signal input configures the
buffer for a gain of -1V/V (Figure 1b).
Since the inverting input exhibits a 500
input imped-
ance, terminate the input with a 56
resistor when con-
figured for an inverting gain in 50
applications
(terminate with 88
in 75 applications). Terminate the
input with a 49.9
resistor in the noninverting case.
Output terminating resistors should directly match
cable impedances in either configuration.
Layout Techniques
Maxim recommends using microstrip and stripline tech-
niques to obtain full bandwidth. To ensure the PC
board does not degrade the buffer’s performance,
design it for a frequency greater than 1GHz. Pay care-
ful attention to inputs and outputs to avoid large para-
sitic capacitance. Whether or not you use a constant-
impedance board, observe the following guidelines
when designing the board:
Don’t use wire-wrapped boards. They are too induc-
tive.
Don’t use IC sockets. They increase parasitic capac-
itance and inductance.
Use surface-mount instead of through-hole compo-
nents for better high-frequency performance.
Use a PC board with at least two layers; it should be
as free from voids as possible.
Keep signal lines as short and as straight as possi-
ble. Do not make 90° turns; round all corners.
Input Voltage Range and Output Swing
The MAX4214 family’s input range extends from
(VEE - 100mV) to (VCC - 2.25V). Input ground sensing
increases the dynamic range for single-supply applica-
tions. The outputs drive a 2k
load to within 60mV of
the power-supply rails. With smaller resistive loads, the
output swing is reduced as shown in the Electrical
Characteristics and Typical Operating Characteristics.
MAX4214/MAX4215/MAX4217/MAX4219/MAX4222
High-Speed, Single-Supply, Gain of 2,
Closed-Loop, Rail-to-Rail Buffers with Enable
_______________________________________________________________________________________
9
MAX42_ _
500
500
IN-
OUT
RO
RTO
OUT
IN
RTIN
IN+
Figure 1a. Noninverting Gain Configuration (AV = +2V/V)
MAX42_ _
500
500
OUT
RO
RTO
OUT
RS
RTIN
IN+
IN-
IN
Figure 1b. Inverting Gain Configuration (AV = -1V/V)
相關PDF資料 |
PDF描述 |
|---|---|
| 31270 | CONN RING 16-22 AWG #8 D-GRIP |
| 31518 | CONN RING 22-26 AWG #2 D-GRIP |
| AGC-1-3/4-R | FUSE 1.75A 250V GLASS FAST |
| 30928 | CONN RING 14-16 AWG #10 D-GRIP |
| AGC-1-6/10-R | FUSE 1.6A 250V GLASS FAST |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX421C/D | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX421CPD | 功能描述:運算放大器 - 運放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX421CPD+ | 功能描述:運算放大器 - 運放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX421CWE | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX421CWE+ | 功能描述:運算放大器 - 運放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。