- 您現在的位置：買賣IC網 > PDF目錄5516 > MAX4223ESA+T (Maxim Integrated Products)IC AMP CURRENT FB LP 8-SOIC PDF資料下載
參數資料
| 型號： | MAX4223ESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/20頁 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT FB LP 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電流反饋 |
| 電路數： | 1 |
| 轉換速率： | 1100 V/µs |
| -3db帶寬： | 1GHz |
| 電流 - 輸入偏壓： | 4µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 6mA |
| 電流 - 輸出 / 通道： | 80mA |
| 電壓 - 電源，單路/雙路(±)： | ±2.85 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
MAX4223–MAX4228
1GHz, Low-Power, SOT23,
Current-Feedback Amplifiers with Shutdown
10
______________________________________________________________________________________
_______________Detailed Description
The MAX4223–MAX4228 are ultra-high-speed, low-
power, current-feedback amplifiers featuring -3dB
bandwidths up to 1GHz, 0.1dB gain flatness up to
300MHz, and very low differential gain and phase
errors of 0.01% and 0.02°, respectively. These devices
operate on dual ±5V or ±3V power supplies and
require only 6mA of supply current per amplifier. The
MAX4223/MAX4225/MAX4226 are optimized for
closed-loop gains of +1 (0dB) or more and have -3dB
bandwidths of 1GHz. The MAX4224/MAX4227/
MAX4228 are optimized for closed-loop gains of +2
(6dB) or more, and have -3dB bandwidths of 600MHz
(1.2GHz gain-bandwidth product).
The current-mode feedback topology of these ampli-
fiers allows them to achieve slew rates of up to
1700V/s with corresponding large signal bandwidths
up to 330MHz. Each device in this family has an output
that is capable of driving a minimum of 60mA of output
current to ±2.5V.
Theory of Operation
Since the MAX4223–MAX4228 are current-feedback
amplifiers, their open-loop transfer function is
expressed as a transimpedance:
The frequency behavior of this open-loop transimped-
ance is similar to the open-loop gain of a voltage-feed-
back amplifier. That is, it has a large DC value and
decreases at approximately 6dB per octave.
Analyzing the current-feedback amplifier in a gain con-
figuration (Figure 1) yields the following transfer func-
tion:
At low gains, (G x RIN-) << RF . Therefore, unlike tradi-
tional voltage-feedback amplifiers, the closed-loop
bandwidth is essentially independent of the closed-
loop gain. Note also that at low frequencies, TZ >> [(G
x RIN-) + RF], so that:
Low-Power Shutdown Mode
The MAX4223/MAX4224/MAX4226/MAX4228 have a
shutdown mode that is activated by driving the SHDN
input low. When powered from ±5V supplies, the SHDN
input is compatible with TTL logic. Placing the amplifier
in shutdown mode reduces quiescent supply current to
350A typical, and puts the amplifier output into a high-
impedance state (100k
typical). This feature allows
these devices to be used as multiplexers in wideband
systems. To implement the mux function, the outputs of
multiple amplifiers can be tied together, and only the
amplifier with the selected input will be enabled. All of
the other amplifiers will be placed in the low-power
shutdown mode, with their high output impedance pre-
senting very little load to the active amplifier output. For
gains of +2 or greater, the feedback network imped-
ance of all the amplifiers used in a mux application
must be considered when calculating the total load on
the active amplifier output.
__________Applications Information
Layout and Power-Supply Bypassing
The MAX4223–MAX4228 have an extremely high band-
width, and consequently require careful board layout,
including the possible use of constant-impedance
microstrip or stripline techniques.
V
G
R
OUT
IN
F
G
=
+
1
.
V
G x
T
S
T
S
G x R
R
where G
A
R
OUT
IN
Z
IN
F
V
F
G
=
( )
( ) +
+
=
+
1
V
I
or T
OUT
IN
Z
MAX4223
MAX4224
MAX4225
MAX4226
MAX4227
MAX4228
RG
IN-
TZ
RIN-
OUT
+1
IN+
VIN
RF
+1
Figure 1. Current-Feedback Amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| 6648056-1 | CONN,SKT |
| 320571 | CONN RING 16-22 AWG #1/4 PIDG |
| LPSJ301.ZXID | FUSEHOLDER CLASS J 30A 1POLE |
| 31894 | CONN RING 16-22 AWG #1/4 PIDG |
| MAX9633ATA+T | IC OPAMP GP 27MHZ LN 8TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4223EUT | 制造商:Maxim Integrated Products 功能描述:NON BOOK, REQUIRES Q#, NC/NR - Cut Tape Product |
| MAX4223EUT+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL CURRENT FDBK 5.5V 6PIN SOT-23 - Rail/Tube |
| MAX4223EUT+T | 功能描述:高速運算放大器 1GHz Current Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4223EUT-T | 功能描述:高速運算放大器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4223EVKIT | 功能描述:高速運算放大器 Programmers, Development Systems RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。