- 您現在的位置：買賣IC網 > PDF目錄5516 > MAX4224ESA+T (Maxim Integrated Products)IC AMP CURRENT FB LP 8-SOIC PDF資料下載
參數資料
| 型號： | MAX4224ESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/20頁 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT FB LP 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電流反饋 |
| 電路數： | 1 |
| 轉換速率： | 1700 V/µs |
| -3db帶寬： | 600MHz |
| 電流 - 輸入偏壓： | 4µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 6mA |
| 電流 - 輸出 / 通道： | 80mA |
| 電壓 - 電源，單路/雙路(±)： | ±2.85 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
MAX4223–MAX4228
1GHz, Low-Power, SOT23,
Current-Feedback Amplifiers with Shutdown
______________________________________________________________________________________
11
To realize the full AC performance of these high-speed
amplifiers, pay careful attention to power-supply
bypassing and board layout. The PC board should
have at least two layers: a signal and power layer on
one side and a large, low-impedance ground plane on
the other. The ground plane should be as free of voids
as possible, with one exception: the inverting input pin
(IN-) should have as low a capacitance to ground as
possible. This means that there should be no ground
plane under IN- or under the components (RF and RG)
connected to it. With multilayer boards, locate the
ground plane on a layer that incorporates no signal or
power traces.
Whether or not a constant-impedance board is used, it
is best to observe the following guidelines when
designing the board:
1) Do not use wire-wrapped boards (they are too
inductive) or breadboards (they are too capacitive).
2) Do not use IC sockets. IC sockets increase reac-
tance.
3) Keep signal lines as short and straight as possible.
Do not make 90° turns; round all corners.
4) Observe high-frequency bypassing techniques to
maintain the amplifier’s accuracy and stability.
5) In general, surface-mount components have shorter
bodies and lower parasitic reactance, giving better
high-frequency performance than through-hole com-
ponents.
The bypass capacitors should include a 10nF ceramic,
surface-mount capacitor between each supply pin and
the ground plane, located as close to the package as
possible. Optionally, place a 10F tantalum capacitor
at the power-supply pins’ point of entry to the PC board
to ensure the integrity of incoming supplies. The power-
supply trace should lead directly from the tantalum
capacitor to the VCC and VEE pins. To minimize para-
sitic inductance, keep PC traces short and use surface-
mount components. The N.C. pins should be
connected to a common ground plane on the PC board
to minimize parasitic coupling.
If input termination resistors and output back-termina-
tion resistors are used, they should be surface-mount
types, and should be placed as close to the IC pins as
possible. Tie all N.C. pins to the ground plane to mini-
mize parasitic coupling.
Choosing Feedback and Gain Resistors
As with all current-feedback amplifiers, the frequency
response of these devices depends critically on the
value of the feedback resistor RF. RF combines with an
internal compensation capacitor to form the dominant
pole in the feedback loop. Reducing RF’s value
increases the pole frequency and the -3dB bandwidth,
but also increases peaking due to interaction with other
nondominant poles. Increasing RF’s value reduces
peaking and bandwidth.
Table 1 shows optimal values for the feedback resistor
(RF) and gain-setting resistor (RG) for the MAX4223–
MAX4228. Note that the MAX4224/MAX4227/MAX4228
offer superior AC performance for all gains except unity
gain (0dB). These values provide optimal AC response
using surface-mount resistors and good layout tech-
niques. Maxim’s high-speed amplifier evaluation kits
provide practical examples of such layout techniques.
Stray capacitance at IN- causes feedback resistor
decoupling and produces peaking in the frequency-
response curve. Keep the capacitance at IN- as low as
possible by using surface-mount resistors and by
avoiding the use of a ground plane beneath or beside
these resistors and the IN- pin. Some capacitance is
unavoidable; if necessary, its effects can be counter-
acted by adjusting RF. Use 1% resistors to maintain
consistency over a wide range of production lots.
Table 1. Optimal Feedback Resistor
Networks
MAX4223/MAX4225/MAX4226
2
6
200
380
115
GAIN
(dB)
RG
(
)
RF
(
)
0.1dB
BW
(MHz)
GAIN
(V/V)
-3dB
BW
(MHz)
5
14
100
25
235
65
2
6
470
600
200
5
14
240
62
400
90
10
20
130
15
195
35
MAX4224/MAX4227/MAX4228
*
For the MAX4223EUT, this optimal value is 470
.
1
0
560*
Open
1000
300
相關PDF資料 |
PDF描述 |
|---|---|
| 34484 | CONN RING 14-12 AWG #10 SOLIS |
| 5532433-7 | CONN HDI PLUG 150POS 3ROW VERT |
| 2-33460-2 | CONN RING 8 AWG #10 SOLIS |
| MAX4223ESA+T | IC AMP CURRENT FB LP 8-SOIC |
| 6648056-1 | CONN,SKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4224ESA-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4224EUT | 制造商:Maxim Integrated Products 功能描述:NON BOOK, Q# REQ'D, NC/NR - Rail/Tube |
| MAX4224EUT+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL CURRENT FDBK 5.5V 6PIN SOT-23 - Cut Tape Product |
| MAX4224EUT+T | 功能描述:高速運算放大器 1GHz Current Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4224EUT-T | 功能描述:運算放大器 - 運放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。