參數資料
型號: MAX4433EUA+T
廠商: Maxim Integrated Products
文件頁數: 12/12頁
文件大?。?/td> 0K
描述: IC OP AMP DUAL 180MHZ 8UMAX
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
放大器類型: 電壓反饋
電路數: 2
轉換速率: 145 V/µs
-3db帶寬: 215MHz
電流 - 輸入偏壓: 11µA
電壓 - 輸入偏移: 1250µV
電流 - 電源: 11mA
電流 - 輸出 / 通道: 60mA
電壓 - 電源,單路/雙路(±): 9 V ~ 11 V,±4.5 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 帶卷 (TR)
Detailed Description
The MAX4430–MAX4433 are wide-bandwidth, ultra-low-
distortion, voltage-feedback amplifiers. The MAX4430/
MAX4432 are internally compensated for unity gain.
The MAX4431/MAX4433 are internally compensated for
gains of +2V/V or greater.
These amplifiers have ultra-fast 37ns (MAX4430/
MAX4432) 16-bit settling times, 100dB SFDR at 1MHz,
and 4Vp-p output swing with minimum 110dB open-
loop gain.
High-Speed ADC Input Driver Application
The MAX4430–MAX4433 op amps are ideal for driving
high-speed 14- to 16-bit ADCs. In most cases, these
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the
input. The driver used must withstand these changing
capacitive loads while holding the signal amplitude sta-
bility consistent with the ADC’s resolution and, at the
same time, have a frequency response compatible with
the sampling speed of the ADC (Figure 1).
Inverting and Noninverting Configurations
The circuits typically used for the inverting and non-
inverting configurations of the MAX4430–MAX4433 are
shown in Figures 2a and 2b. The minimum uncondition-
ally stable gain values are 1 for the MAX4430/MAX4432
and 2 for the MAX4431/MAX4433. Use care in selecting
the value for the resistor marked RS in both circuits.
From dynamic stability considerations (based on the
part’s frequency response and the input capacitance of
the MAX4430–MAX4433), the maximum recommended
value for RS is 500
. In general, lower RS values will
yield a higher bandwidth and better dynamic stability,
at the cost of higher power consumption, higher power
dissipation in the IC, and reduced output drive avail-
ability. For a minimum RS value, take into consideration
that the current indicated as IF is supplied by the output
stage and must be discounted from the maximum out-
put current to calculate the maximum current available
to the load. IF can be found using the following equa-
tion:
IF = VIN(MAX) / RS
If DC thermal stability is an important design concern,
the Thevenin resistance seen by both inputs at DC
must be balanced. This includes the resistance of the
signal source and termination resistors if the amplifier
signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
be considered as a possible limitation to the available
bandwidth or to the dynamic stability. Only resistors
with small parallel capacitance specifications should
be considered.
Applications Information
Layout and Power-Supply Bypassing
The MAX4430–MAX4433 have wide bandwidth and
consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
pay careful attention to power-supply bypassing and
board layout. The PC board should have a large low-
impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
MAX4430–MAX4433
Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
_______________________________________________________________________________________
9
+VCC
-VEE
HIGH-SPEED
14/16-BIT ADC
Figure 1. Typical Application Circuit
VOUT
VIN
RS
RF
IF
RF
RS
VOUT
VIN
=
A = 1 +
Figure 2a. Noninverting Configuration
- RF
RS
VOUT
VIN
VOUT
VIN
RB
RF
RS
IF
=
A =
Figure 2b. Inverting Configuration
相關PDF資料
PDF描述
5532436-1 CONN PLUG HDI 100POS 4ROW VERT
RCWL2512R620JNEA RES .62 OHM 1W 5% 2512 SMD
RCWL2512R560JNEA RES .56 OHM 1W 5% 2512 SMD
MAX4436EUA+T IC OP AMP DUAL 150MHZ 8UMAX
6367555-2 ASSY Z-DOK+6 ADAPTER BRD 40PR
相關代理商/技術參數
參數描述
MAX4434ESA 功能描述:高速運算放大器 Dual-Supply 150MHz 16-Bit Accurate RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4434ESA-T 功能描述:高速運算放大器 Dual-Supply 150MHz 16-Bit Accurate RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4434EUK 制造商:Maxim Integrated Products 功能描述:SINGLE-SUPPLY 150MHZ 16-BIT ACCUR - Rail/Tube
MAX4434EUK/V+T 功能描述:高速運算放大器 Dual-Supply 150MHz 16-Bit Accurate RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4434EUK+ 制造商:Maxim Integrated Products 功能描述:OP AMP SGL VOLT FDBK 5.5V 5PIN SOT-23 - Rail/Tube