- 您現在的位置：買賣IC網 > PDF目錄11164 > MAX4504CSA+T (Maxim Integrated Products)IC SWITCH SPST 8SOIC PDF資料下載
參數資料
| 型號： | MAX4504CSA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH SPST 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 1 x SPST- NC |
| 導通狀態電阻： | 250 歐姆 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±1 V ~ 6 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
__________Applications Information
Power-Supply Considerations
The MAX4503/MAX4504’s construction is typical of
most CMOS analog switches, except they have only
two supply pins: V+ and V-. These voltages set the
analog voltage limits of the switch. Reverse ESD-pro-
tection diodes are internally connected between IN and
each analog signal pin and both V+ and V-. If any ana-
log signal exceeds V+ or V-, one of these diodes will
conduct. During normal operation, these (and other)
reverse-biased ESD diodes leak, forming the only cur-
rent drawn from V-. Additional current flows through V+
from the logic-level translator.
Virtually all the analog leakage current is provided
through the ESD diodes. Although the ESD diodes on a
given signal pin are identical and therefore fairly well
balanced, they are reverse biased differently. Each is
biased by either V+ or V- and the analog signal. This
means their leakages will vary as the signal varies. The
difference in the two diode leakages to the V+ and V-
pins constitutes the analog-signal-path leakage current.
All analog leakage current flows between each pin and
one of the supply terminals, not to the other switch ter-
minal. This is why both sides of a given switch can
show leakage currents of either the same or opposite
polarity.
There is no connection between the analog signal
paths and V+ or V-.
V+ and V- also power the internal logic and logic-level
translators. Since there is no ground pin, the logic input
has a low-current pull-up to V+ and the logic limit is set
by an internal comparator referenced to V+. The logic-
level translators convert the logic levels to switched V+
and V- signals, to drive the gates of the analog signals.
This drive signal is the only connection between the
logic supplies (and signals) and the analog supplies.
COM, NO, and NC pins have ESD-protection diodes to
V+ and V-.
The logic is CMOS compatible when V+ is +5V. CMOS
compatibility is maintained with all V+ values, assuming
that the CMOS logic is operated from the same V+ sup-
ply. Since the MAX4503/MAX4504 have no ground
pins, the logic levels are internally referenced to V+.
Do not connect the MAX4503/MAX4504 V+ to +3V
and connect the logic-level pins to TTL-logic-level
signals. TTL levels can exceed +3V and violate the
absolute maximum ratings, damaging the part
and/or external circuits.
High-Frequency Performance
In 50
systems, signal response is reasonably flat up
to 50MHz. (see Typical Operating Characteristics).
Above 20MHz the on-response has several minor
peaks which are highly layout dependent. The problem
is not in turning the switch on, but in turning it off. The
off-state switch acts like a capacitor, and passes higher
frequencies with less attenuation. At 10MHz, off isola-
tion is about -65dB in 50
systems, becoming worse
(approximately 20dB per decade) as frequency
increases. Higher circuit impedances also make off iso-
lation worse.
MAX4503/MAX4504
Low-Voltage, Dual-Supply, SPST,
CMOS Analog Switches
6
_______________________________________________________________________________________
______________________________________________________________Pin Description
MAX4503
DIP/SO
SOT23-5
FUNCTION
1
Analog Switch Common Terminal
2, 3, 5
—
No Connect (not internally connected)
8
2
Analog Switch Normally Open Terminal
7
3
Negative (analog) Supply Voltage Input
6
4
Digital Control Input
4
5
Positive (analog and digital) Supply Voltage Input
—
Analog Switch Normally Closed Terminal
MAX4504
DIP/SO
SOT23-5
PIN
1
2, 3, 5
—
7
3
6
4
5
8
2
NAME
COM
N.C.
NO
V-
IN
V+
NC
Note: NO, NC, and COM pins are identical and interchangeable. Either may be considered as an input or output; signals pass
equally well in both directions.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B44-CU-B1 | CONVERTER MOD DC/DC 48V 200W |
| MAX4646EUK-T | IC SWITCH SPST SOT23-5 |
| VE-B13-CU-B1 | CONVERTER MOD DC/DC 24V 200W |
| MAX4504CSA+ | IC SWITCH SPST 8SOIC |
| EFM32TG210F16 | MCU 32BIT 16KB FLASH 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4504CUK | 制造商:Maxim Integrated Products 功能描述:NORMALLY CLOSED LOW-VOLTAGE DUAL-S - Cut Tape Product |
| MAX4504CUK+ | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, DUAL-SUPPLY, SPST, CMOS ANALOG SWITCHES - Rail/Tube |
| MAX4504CUK+T | 功能描述:模擬開關 IC Low-Voltage SPST CMOS Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4504CUK-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4504CUK-TW | 制造商:Maxim Integrated Products 功能描述:NORMALLY CLOSED LOW-VOLTAGE, DUAL-SUPPLY, SPS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。