- 您現在的位置：買賣IC網 > PDF目錄383416 > MAX4618CPE (MAXIM INTEGRATED PRODUCTS INC) High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches PDF資料下載
參數資料
| 型號： | MAX4618CPE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
| 中文描述： | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 179K |
| 代理商： | MAX4618CPE |
M
High-Speed, Low-Voltage, CMOS Analog
Multiplexers/Switches
_______________________________________________________________________________________
9
The logic-level thresholds are TTL/CMOS compatible
when V
CC
is +5V. As V
CC
rises, the threshold increas-
es; as V
CC
falls, the threshold decreases. For example,
when V
CC
= +3V the guaranteed minimum logic-high
threshold decreases to 2.0V
Power Supply
These devices operate from a single supply between
+2.5V and +5.5V. All of the bipolar precautions must be
observed. At room temperature, they actually “work”
with a single supply near or below +2V, although as
supply voltage decreases, switch on-resistance
becomes very high.
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V
CC
on first, followed by the logic
inputs and analog signals. If power-supply sequencing
is not possible, add two small signal diodes (D1, D2) in
series with the supply pins for overvoltage protection
(Figure 1).
Adding diodes reduces the analog-signal range to one
diode drop below V
CC
and one diode drop above
GND, but does not affect the devices’ low switch resis-
tance and low leakage characteristics. Device opera-
tion is unchanged, and the difference between V
CC
and GND should not exceed 6V. These protection
diodes are not recommended if signal levels must
extend to ground.
High-Frequency Performance
In 50
systems, signal response is reasonably flat up
to 50MHz (see Typical Operating Characteristics).
Above 20MHz, the on-response has several minor
peaks that are highly layout dependent. The problem is
not turning the switch on, but turning it off. The off-state
switch acts like a capacitor and passes higher frequen-
cies with less attenuation. At 10MHz, off-isolation is
about -50dB in 50
systems, becoming worse (approx-
imately 20dB per decade) as frequency increases.
Higher circuit impedances also degrade off-isolation.
Adjacent channel attenuation is about 3dB above that
of a bare IC socket and is entirely due to capacitive
coupling.
Pin Nomenclature
The MAX4617/MAX4618/MAX4619 are pin compatible
with the industry-standard 74HC4051/74HC4052/
74HC4053 and the MAX4581/MAX4582/MAX4583. In
single-supply applications, they function identically and
have identical logic diagrams, although these parts dif-
fer electrically.
The pin designations and logic diagrams in this data
sheet conform to the original 1972 specifications pub-
lished by RCA for the CD4051/CD4052/CD4053. These
designations differ from the standard Maxim switch and
mux designations found on other Maxim data sheets
(including the MAX4051/MAX4052/MAX4053) and may
cause confusion. Designers who feel more comfortable
with Maxim’s standard designations are advised that
the pin designations and logic diagrams on the
MAX4051/MAX4052/MAX4053 data sheet may be freely
applied to the MAX4617/MAX4618/MAX4619.
X, Y, Z
X_, Y_, Z_
V
EE
V
CC
*INTERNAL PROTECTION DIODES
D2
EXTERNAL
BLOCKING DIODE
D1
EXTERNAL
BLOCKING DIODE
GND
V
CC
MAX4617
MAX4618
MAX4619
*
*
*
*
Figure 1. Overvoltage Protection Using External Blocking
Diodes
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4618CSE | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
| MAX4618CUE | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
| MAX4618EPE | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
| MAX4618ESE | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
| MAX4618EUE | High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4618CPE+ | 功能描述:多路器開關 IC 4:1 2Ch Low Voltage Analog MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX4618CSE | 功能描述:多路器開關 IC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX4618CSE+ | 功能描述:多路器開關 IC 4:1 2Ch Low Voltage Analog MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX4618CSE+T | 功能描述:多路器開關 IC 4:1 2Ch Low Voltage Analog MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX4618CSE-T | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。