- 您現在的位置：買賣IC網 > PDF目錄383421 > MAX4750ETE (MAXIM INTEGRATED PRODUCTS INC) 3.3-V Can Transceiver 8-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | MAX4750ETE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3.3-V Can Transceiver 8-SOIC -40 to 85 |
| 中文描述： | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, QCC16 |
| 封裝： | 4 X 4 MM, 0.8 MM HEIGHT, MO220WGGC, QFN-16 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 342K |
| 代理商： | MAX4750ETE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁
M
50
Low-Voltage, Quad S PS T /Dual S PDT Analog
S witc hes in UCS P
_______________________________________________________________________________________
9
Applic ations Information
Operating Considerations for
High-V oltage S upply
The MAX4747–MAX4750 operate to +11V with some
precautions. The absolute maximum rating for V+ is
+12V (referenced to GND). When operating near this
region, bypass V+ with a minimum 0.1μF capacitor to
ground as close to the IC as possible.
Logic Levels
The MAX4747–MAX4750 are TTL compatible when
powered from a single +3V supply. When powered from
other supply voltages, the logic inputs should be driven
rail-to-rail. For example, with a +11V supply, IN_ should
be driven low to 0V and high to 11V. With a +3.3V sup-
ply, IN_ should be driven low to 0V and high to 3.3V.
Driving IN_ rail-to-rail minimizes power consumption.
Analog S ignal Levels
Analog signals that range over the entire supply volt-
age (GND to V+) pass with very little change in R
ON
(see the
Typical Operating Characteristics
). The bidi-
rectional switches allow NO_, NC_, and COM_ connec-
tions to be used as either inputs or outputs.
Power-S upply S equenc ing and
Overvoltage Protec tion
CAUTION: Do not exceed the absolute maximum
ratings. Stresses beyond the listed ratings can
cause permanent damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals, especially if the analog signal is not
current limited. If this sequencing is not possible, and if
the analog inputs are not current limited to <20mA, add
small-signal diode D1 as shown in Figure 1. If the ana-
log signal can dip below GND, add D2. Adding protec-
tion diodes reduces the analog signal range to a diode
drop (about 0.7V) below V+ (for D1), and to a diode
drop above ground (for D2). Leakage is unaffected by
adding the diodes. On-resistance increases slightly at
low supply voltages. Maximum supply voltage (V+)
must not exceed +11V.
Adding protection diodes causes the logic thresholds to
be shifted relative to the power-supply rails. The most
significant shift occurs when using low supply voltages
(+5V or less). With a +5V supply, TTL compatibility is
not guaranteed when protection diodes are added.
Driving IN_ and IN_ all the way to the supply rails (i.e., to
a diode drop higher than the V+ pin, or to a diode drop
lower than the GND pin) is always acceptable.
Protection diodes D1 and D2 also protect against some
overvoltage situations. Using the circuit in Figure 1, no
damage results if the supply voltage is below the
absolute maximum rating (+12V) and if a fault voltage
up to the absolute maximum rating (V+ + 0.3V) is
applied to an analog signal terminal.
UCS P Applic ations Information
For the latest application details on UCSP construction,
dimensions, tape carrier information, PC board tech-
niques, bump-pad layout, and recommended reflow
temperature profile, as well as the latest information on
reliability testing results, refer to the Application Note:
UCSP—A Wafer-Level Chip-Scale Package on Maxim’s
web site at www.maxim-ic.com/ucsp.
MAX4747–
MAX4750
NO_
COM_
GND
V+
*INTERNAL PROTECTION DIODES
D2
D1
EXTERNAL BLOCKING DIODE
EXTERNAL BLOCKING DIODE
GND
V+
*
*
*
*
Figure 1. Overvoltage Protection Using External Blocking Diodes
Test Circ uits/T iming Diagrams
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4750EUD | 3.3-V Can Transceiver 8-SOIC -40 to 85 |
| MAX4765EBC-T | Low-Voltage, Dual SPDT, Audio Clickless Switches with Negative Rail Capability |
| MAX4762 | Low-Voltage. Dual SPDT. Audio Clickless Switches with Negative Rail Capability |
| MAX4763 | Low-Voltage. Dual SPDT. Audio Clickless Switches with Negative Rail Capability |
| MAX4764 | Low-Voltage. Dual SPDT. Audio Clickless Switches with Negative Rail Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4750ETE+ | 功能描述:模擬開關 IC Quad SPST/Dual SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4750ETE+T | 功能描述:模擬開關 IC Quad SPST/Dual SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4750ETE-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4750EUD | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4750EUD+ | 功能描述:模擬開關 IC Quad SPST/Dual SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。