- 您現在的位置：買賣IC網 > PDF目錄11157 > MAX4794EUS+T (Maxim Integrated Products)IC ANALOG SWITCH 1X1 SOT143-4 PDF資料下載
參數資料
| 型號： | MAX4794EUS+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ANALOG SWITCH 1X1 SOT143-4 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 功能： | 開關 |
| 電路： | 1 x 1:1 |
| 導通狀態電阻： | 400 毫歐 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.3 V ~ 5.5 V |
| 電流 - 電源： | 80µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | TO-253-4，TO-253AA |
| 供應商設備封裝： | SOT-143-4 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1421 (CN2011-ZH PDF) |
| 其它名稱： | MAX4794EUS+TDKR |
off.
FLAG is an open-drain output transistor and requires
an external pullup resistor from
FLAG to IN. During shut-
down (ON is low), the pulldown on
FLAG output is
released in order to limit power dissipation.
FLAG goes
low when any of the following conditions occur:
The die temperature exceeds the thermal-shutdown
temperature limit of +150°C.
The device is in current limit for more than the fault-
blanking period.
VIN is below UVLO threshold.
Autoretry (MAX4790/MAX4792/MAX4794)
When the forward or reverse current-limit threshold is
exceeded, tBLANK timer begins counting (Figure 2).
The timer resets if the overcurrent condition disappears
before tBLANK has elapsed. A retry time delay, tRETRY,
is started immediately after tBLANK has elapsed and
during that time, the switch is latched off. At the end of
tRETRY, the switch is turned on again. If the fault still
exists, the cycle is repeated. If the fault has been
removed, the switch stays on.
The autoretry feature saves system power in the case of
an overcurrent or short-circuit condition. During tBLANK,
when the switch is on, the supply current is at the cur-
rent limit. During tRETRY, when the switch is off, the cur-
rent through the switch is zero. Instead of observing the
full load current, the switch sees the equivalent load
current times duty cycle or ISUPPLY = ILOAD
tBLANK/(tBLANK + tRETRY). With a typical tBLANK =
37ms and typical tRETRY = 259ms, the duty cycle is
12%, which results in an 88% power savings over the
switch being on the entire time. The duty cycle is con-
sistent across the process and devices.
Latch Off (MAX4789/MAX4791/MAX4793)
When the forward or reverse current-limit threshold is
exceeded, tBLANK timer begins counting. The timer
resets if the overcurrent condition disappears before
tBLANK has elapsed. The switch is shut off if the over-
current condition continues up to the end of the blank-
ing time. Reset the switch by either toggling ON (Figure
3a) or cycling the input voltage below UVLO, typically
2V (Figure 3b).
Fault Blanking
The MAX4789–MAX4794 feature 14ms (min) fault blank-
ing. Fault blanking allows current-limit faults, including
momentary short-circuit faults that occur when hot
swapping a capacitive load, and also ensures that no
fault is issued during power-up. When a load transient
causes the device to enter current limit, an internal
counter starts. If the load-transient fault persists beyond
the fault-blanking timeout, the MAX4789/MAX4791/
MAX4793
FLAG asserts low. Load-transient faults less
than tBLANK do not cause a FLAG output assertion. Only
current-limit faults are blanked.
A thermal fault and input voltage drops below the UVLO
threshold cause
FLAG to assert immediately and do not
wait for the blanking time.
Thermal Shutdown
The MAX4789–MAX4794 have a thermal shutdown fea-
ture to protect the devices from overheating. The switch
turns off and
FLAG goes low immediately (no fault blank-
ing) when the junction temperature exceeds +150°C.
The switch turns back on when the device temperature
drops approximately 15°C.
MAX4789–MAX4794
200mA/250mA/300mA Current-Limit Switches
_______________________________________________________________________________________
7
ON
FAULT
SWITCH ON/OFF
SUPPLY CURRENT MODE
Low
X
OFF
Shutdown
High
Undervoltage Lockout
OFF
Shutdown
High
Thermal
OFF immediately (tBLANK period does not apply)
Latch off
OFF after tBLANK period has elapsed
Latch off
High
Current Limit
ON during tBLANK period, OFF during tRETRY period for the
MAX4790, MAX4792, and MAX4794; cycle repeats until fault
is removed
See the Autoretry section
Table 1. MAX4789–MAX4794 Switch Truth Table
LOAD
CURRENT
SWITCH
STATUS
tBLANK
OFF
ON
tRETRY
CURRENT
LIMIT
SHORT
CONDITION
REMOVED
tBLANK
Figure 2. MAX4790/MAX4792/MAX4794 Autoretry Fault
Blanking Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC932A1FHN,151 | IC 80C51 MCU FLASH 8K 28HVQFN |
| C8051F553-IM | IC 8051 MCU 32K FLASH 24-QFN |
| EFM32G200F16 | MCU 32BIT 16KB FLASH 32-QFN |
| C8051F231-GQR | IC 8051 MCU 8K FLASH 32LQFP |
| C8051F543-IM | IC 8051 MCU 16K FLASH 24-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4795ETT-T | 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX4795EUK | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX4795EUK+ | 制造商:Maxim Integrated Products 功能描述:CURRENT LIMIT SW 1-IN 1-OUT 2V TO 4.5V 0.72A 5PIN SOT-23 - Rail/Tube 制造商:Maxim Integrated Products 功能描述:450MA/500MA CURRENT-LIMIT SWITCHES |
| MAX4795EUK+T | 功能描述:電源開關 IC - 配電 450mA/500mA Current Limit Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX4795EUK-T | 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。