M
450mA/500mA Current-Limit Switches
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
IN, ON,
FLAG
, OUT to GND.....................................-0.3V to +6V
OUT Short Circuit to GND.................................Internally Limited
Continuous Power Dissipation (T
A
= +70
°
C)
5-Pin SOT23 (derate 7.1mW/
°
C above +70
°
C)............571mW
6-Pin TDFN (derate 24.4mW/
°
C above +70
°
C) .........1951mW
ELECTRICAL CHARACTERISTICS
(V
IN
= +2.0V to +4.5V, T
A
= -40
°
C to +85
°
C, unless otherwise noted. Typical values are at V
IN
= 3.3V, T
A
= +25
°
C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1:
All parts are 100% tested at +25
°
C. Electrical limits across the full temperature range are guaranteed by design and correlation.
Note 2:
Latch-off current does not include the current flowing into
FLAG
.
Note 3:
TDFN packages are guaranteed by design.
Note 4:
The on-time is defined as the time taken for the current through the switch to go from 0mA to full load. The off-time is defined as
the time taken for the current through the switch to go from full load to 0mA.
Note 5:
Retry time is typically 15 times the blanking time.
Operating Temperature Range ...........................-40
°
C to +85
°
C
Junction Temperature......................................................+150
°
C
Storage Temperature Range.............................-65
°
C to +150
°
C
Lead Temperature (soldering, 10s).................................+300
°
C
PARAMETER
SYMBOL
V
IN
I
Q
CONDITIONS
MIN
2.0
TYP
MAX
4.5
125
UNITS
V
μA
Operating Voltage
Quiescent Current
V
ON
= V
IN
, I
OUT
= 0, switch on
V
ON
= V
IN
, after an overcurrent
fault (MAX4795/MAX4797) (Note 2)
V
IN
= +3.3V
80
Latch-Off Current
I
LATCH
V
IN
= +3.3V
6
10
μA
Shutdown Current
I
SHDN
V
ON
= 0V
MAX4795/MAX4796, V
IN
= 3.3V, V
OUT
= GND
MAX4797/MAX4798, V
IN
= 3.3V, V
OUT
= GND
MAX4795/MAX4796
MAX4797/MAX4798
0.03
1
μA
450
500
720
800
720
800
+1
1
1
0.4
0.36
Forward Current Limit
mA
Reverse Current Limit
mA
ON Input Leakage
Shutdown Forward Leakage
Shutdown Reverse Leakage
-1
μA
μA
μA
V
ON
= 0V, V
OUT
= 0V
V
ON
= 0V, V
IN
= 2V, V
OUT
= 4.5V
MAX4795/MAX4796, I
LOAD
= 100mA
MAX4797/MAX4798, I
L OA D
= 100m A
V
IN
= +2V to +3.6V
V
IN
> 3.6V
0.01
0.2
0.18
On-Resistance (Note 3)
R
ON
1.4
2
ON Input Logic High Voltage
V
IH
V
ON Input Logic Low Voltage
FLAG
Output Logic Low Voltage
V
IL
0.5
0.4
V
V
I
S N K
= 1m A
FLAG
Output High Leakage
Current
V
IN
= V
F LAG
= V
ON
= 4.5V
1
μA
Thermal Shutdown
Thermal-Shutdown Hysteresis
DYNAMIC
Turn-On Time
Turn-Off Time
Blanking Time
150
15
°
C
°
C
V
ON
fr om l ow to hi g h; I
OU T
= 10m A, C
L
= 0.1μF ( N ote 4)
V
ON
fr om hi g h to l ow I
OU T
= 10m A, C
L
= 0.1μF ( N ote 4)
Overcurrent fault; Figures 2, 3
120
100
μs
ns
ms
t
BLANK
14
60
Short-Circuit Current-Limit
Response Time
V
ON
= V
IN
, short circuit applied to OUT
5
μs
Retry Time
t
RETRY
MAX4796/MAX4798, Figure 2 (Note 5)
210
900
ms