- 您現在的位置：買賣IC網 > PDF目錄5513 > MAX492ESA (Maxim Integrated Products)IC OPAMP DUAL MICROPWR R/R 8SOIC PDF資料下載
參數資料
| 型號： | MAX492ESA |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/17頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP DUAL MICROPWR R/R 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.2 V/µs |
| 增益帶寬積： | 500kHz |
| 電流 - 輸入偏壓： | 25nA |
| 電壓 - 輸入偏移： | 200µV |
| 電流 - 電源： | 150µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 6 V，±1.35 V ~ 3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
10
______________________________________________________________________________________
MAX495
10k
1
5
NULL
VEE
4
NULL
Figure 2. Offset Null Circuit
__________Applications Information
The dual MAX492, quad MAX494, and single MAX495
op amps combine excellent DC accuracy with rail-to-
rail operation at both input and output. With their preci-
sion performance, wide dynamic range at low supply
voltages, and very low supply current, these op amps
are ideal for battery-operated equipment and other low-
voltage applications.
Rail-to-Rail Inputs and Outputs
The MAX492/MAX494/MAX495’s input common-mode
range extends 0.25V beyond the positive and negative
supply rails, with excellent common-mode rejection.
Beyond the specified common-mode range, the out-
puts are guaranteed not to undergo phase reversal or
latchup. Therefore, the MAX492/MAX494/MAX495 can
be used in applications with common-mode signals at
or even beyond the supplies, without the problems
associated with typical op amps.
The MAX492/MAX494/MAX495’s output voltage swings
to within 50mV of the supplies with a 100k
load. This
rail-to-rail swing at the input and output substantially
increases the dynamic range, especially in low supply-
voltage applications. Figure 1 shows the input and out-
put waveforms for the MAX492, configured as a
unity-gain noninverting buffer operating from a single
+3V supply. The input signal is 3.0Vp-p, 1kHz sinusoid
centered at +1.5V. The output amplitude is approxi-
mately 2.95Vp-p.
Input Offset Voltage
Rail-to-rail common-mode swing at the input is obtained
by two complementary input stages in parallel, which
feed a folded cascaded stage. The PNP stage is active
for input voltages close to the negative rail, and the
NPN stage is active for input voltages close to the posi-
tive rail.
The offsets of the two pairs are trimmed; however, there
is some small residual mismatch between them. This
mismatch results in a two-level input offset characteris-
tic, with a transition region between the levels occurring
at a common-mode voltage of approximately 1.3V.
Unlike other rail-to-rail op amps, the transition region
has been widened to approximately 600mV in order to
minimize the slight degradation in CMRR caused by
this mismatch.
To adjust the MAX495’s input offset voltage (500V max
at +25°C), connect a 10k
trim potentiometer between
the two NULL pins (pins 1 and 5), with the wiper con-
nected to VEE (pin 4) (Figure 2). The trim range of this
circuit is ±6mV. External offset adjustment is not avail-
able for the dual MAX492 or quad MAX494.
The input bias currents of the MAX492/MAX494/MAX495
are typically less than 50nA. The bias current flows into
the device when the NPN input stage is active, and it
flows out when the PNP input stage is active. To reduce
the offset error caused by input bias current flowing
through external source resistances, match the effec-
tive resistance seen at each input. Connect resistor R3
between the noninverting input and ground when using
VIN
VOUT
Figure 1. Rail-to-Rail Input and Output (Voltage Follower
Circuit, VCC = +3V, VEE = 0V)
相關PDF資料 |
PDF描述 |
|---|---|
| 5533286-3 | CONN PLUG 128POS R/A .100 T/H |
| 5533061-5 | PIN VERTICAL HDI 3ROW W/O |
| MAX492EPA | IC OPAMP DUAL MICROPWR R/R 8-DIP |
| MAX4431ESA+T | IC OP AMP SGL 180MHZ 8-SOIC |
| MAX4430ESA+T | IC OP AMP SGL 180MHZ 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX492ESA+ | 功能描述:運算放大器 - 運放 Dual uPower Single Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX492ESA+T | 功能描述:運算放大器 - 運放 Dual uPower Single Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX492ESA-T | 功能描述:運算放大器 - 運放 Dual uPower Single Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX492MJA | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4932EBC+T | 功能描述:多路器開關 IC Dual 3:1 Clickless Audio MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。