- 您現在的位置：買賣IC網 > PDF目錄10182 > MAX5406EUM+T (Maxim Integrated Products)IC PROC AUDIO W/PB 48TSSOP PDF資料下載
參數資料
| 型號： | MAX5406EUM+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROC AUDIO W/PB 48TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 音頻處理器 |
| 應用： | 臺式音頻，卡拉 OK，TV |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TFSOP（0.240"，6.10mm 寬） |
| 供應商設備封裝： | 48-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
MAX5406
Audio Processor with Pushbutton Interface
______________________________________________________________________________________
15
Up/Down Interface
The MAX5406 features independent control inputs for
volume, balance, ambience, and tone control. All con-
trol inputs are internally debounced for use with
momentary contact SPST switches. All switch inputs
are pulled up to VLOGIC through 50k
Ω resistors. The
wiper setting advances once per button press held for
up to 1s (see Figures 2a and 2b). Maxim’s SmartWiper
control circuitry allows the wiper to advance at a rate of
4Hz when an input is held low from 1s up to 4s, and at
a rate of 16Hz if the contact is maintained for greater
than 4s without the need of a P (see Figure 3 and
Table 1). The MAX5406 ignores multiple buttons being
pressed. A P can also be used to control the
MAX5406.
Volume Control
The MAX5406 implements dual logarithmic potentiome-
ters for volume control that change the sound level by
2dB per button push (see Table 2).
In volume-control mode, the MAX5406’s wipers move
up and down together (see Figure 4). The balance is
unaffected (see the Balance Control section). Left and
right balance settings are maintained when adjusting
the volume.
Balance Control
In balance-control mode, the MAX5406 uses dual
potentiometers to control balance for the left and right
channels. Pressing BALR increases the right channel
wiper by 1dB and decreases the left channel by 1dB.
This causes the right channel to sound louder than the
left channel by 2dB. The overall volume remains con-
stant when adjusting the balance (Figure 5).
Volume and Balance Interaction
Volume and balance operation is simple. However,
there are some interactions that occur at the extreme
wiper positions. These interactions are described in this
section of the data sheet.
When the volume setting is at the maximum level, the
first command to move the balance toward the left chan-
nel forces the right channel to decrease by 1dB.
Subsequent pressing of BALL causes the right channel
to decrease by 2dB. At this position, shown in the right
column of Figure 6a, the left-channel volume is maxi-
mum, but the actual separation between L and R is 3dB.
At this position, pressing VOLDN restores the actual
balance setting only after VOLDN is pressed at least
half as many times as BALL was (previously) pressed
(shown in the middle and right column of Figure 6b) to
increase the right-channel balance.
The volume and balance interaction is similar when vol-
ume setting is at the minimum level.
Tone Control
The MAX5406 implements a linear potentiometer to
control the bass and treble over a range of ±10dB
using the recommended component values.
Note that the actual response achieved is determined
by the values of both external and internal components
and the design equations are somewhat interactive.
Use the values shown in the Electrical Characteristics
as a good starting point for choosing component val-
ues. These components yield shelf turnovers at 100Hz
(bass) and 10kHz (treble) with a total ±10dB of boost at
100Hz and 10kHz. The shoulder or flat portion of the
response is centered on 1kHz.
The circuit in Figure 7 shows the internal structure of
the tone-control system should modification to the
CONTACT
DURATION
WIPER ACTION
t < tLPW
No motion (debouncing) (Figures 2a and 2b)
tLPW
≤ t ≤ 1s
Wiper changes position once (Figures 2a
and 2b)
1s
≤ t < 4s
Wiper changes position at a rate of 4Hz
(Figure 3)
t
≥4s
Wiper changes position at a rate of 16Hz
(Figure 3)
Table 1. Wiper Action vs. Pushbutton
Contact Duration
POSITION
ATTENUATION (dB)
00
12
24
…..
10 ( Power-on state)
20
…..
30
60
31
62
32 (Mute)
> 90
Table 2. Attenuator Position For Volume
Potentiometers
相關PDF資料 |
PDF描述 |
|---|---|
| ADM4850ARMZ | IC TXRX RS485/422 115KBPS 8MSOP |
| LTC1275ACN#PBF | IC A/D CONV 12BIT SAMPLING 24DIP |
| ADM3310EARUZ-REEL | IC TXRX RS-232 3:5 2.7V 28TSSOP |
| CXC3106A282P | CONN PLUG 14POS STRGHT PIN |
| ADM3315EARUZ-REEL | IC TXRX RS-232 3:3 2.7V 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5407EKA | 制造商:Maxim Integrated Products 功能描述:32-TAP AUDIO LOGARITHMIC TAPER DIGI - Rail/Tube |
| MAX5407EKA+ | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 20KOHM SGL 8PIN SOT-23 - Rail/Tube |
| MAX5407EKA+T | 功能描述:數字電位計 IC 32-Tap Audio Log Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5407EKA-T | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5408EEE | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。