參數資料
型號: MAX5427EUA+T
廠商: Maxim Integrated Products
文件頁數: 7/10頁
文件大?。?/td> 0K
描述: IC POT DGTL 1TIME PROGR 8-UMAX
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
接片: 32
電阻(歐姆): 100k
電路數: 1
溫度系數: 標準值 35 ppm/°C
存儲器類型: 非易失
接口: I²C(芯片選擇,增/減)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-uMAX
包裝: 帶卷 (TR)
MAX5427/MAX5428/MAX5429
The value of the counter is then stored and the wiper
position is maintained.
The wiper performs a make-before-break transition,
ensuring that there is never an open circuit during a tran-
sition from one resistor tap to another. When the wiper is
at either end (max/min) of the resistor array, additional
transitions in the direction of the endpoint do not change
the counter value (the counter does not wrap around).
One-Time Programming
The factory-set default position of the wiper on power-
up is tap 16. However, the power-up position can be
changed once using the one-time programming fea-
ture. After the wiper is moved to the desired position,
the programming sequence is initiated by setting U/
D
high, applying 11V to VPP, and then taking CS low. Five
pulses on
CS (consisting of CS starting from low and
going high for tCH and then low for tCL) program the
device (Figure 4). The programming voltage should
then be taken to zero. After the device is programmed,
VPP can be set to zero or be allowed to float. The wiper
position is still adjustable, but always returns to this
programmed position on power-up.
If the intent is to program the device to a specific wiper
position and not to allow further adjustments, then six
programming pulses are required (as opposed to five),
as shown in Figure 4. The sixth pulse locks the wiper
position and disables the serial interface. This also
allows U/
D and CS to float without any increase in sup-
ply current. Once the lockout bit is set, no further
adjustment to the potentiometer is possible, effectively
changing the potentiometer into a fixed resistor-divider
(Table 1).
One-Time Programmable, Linear-Taper
Digital Potentiometers
6
_______________________________________________________________________________________
VDD
U/D
CS
VW
tUP
tCU
tCI
tIL
tIW
tIH
tIC
Figure 2. Increment Mode Serial Interface Timing Diagram
VDD
U/D
CS
VW
tUP
tCU
tCI
tIH
tIW
tIL
tIC
Figure 3. Decrement Mode Serial Interface Timing Diagram
MODE
POWER-ON
RESET WIPER
POSITION
ADJUSTABLE
WIPER
Factory Default
(Unprogrammed)
Tap 16
Yes
Programmed
(5 Programming Pulses)
Programmed
position
Yes
Lock-Bit Set
(6 Programming Pulses)
Programmed
position
No
Table 1. One-Time Programming Options
相關PDF資料
PDF描述
MAX5428EUA+T IC POT DGTL 1TIME PROGR 8-UMAX
IDT72V71623DA IC DGTL SW 2048X2048 144-TQFP
MS3450W28-9PX CONN RCPT 12POS WALL MNT W/PINS
MS3450W28-9PW CONN RCPT 12POS WALL MNT W/PINS
MAX5429EUA+T IC POT DGTL 1TIME PROGR 8-UMAX
相關代理商/技術參數
參數描述
MAX5427EVKIT 功能描述:數字電位計 IC Evaluation Kit for the MAX5427 MAX5428 MAX5429 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MAX5428EGA 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX5428ETA 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX5428ETA+ 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 50KOHM SGL 8TDFN EP - Rail/Tube
MAX5428ETA+T 功能描述:數字電位計 IC 32-Tap One-Time Programmable RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel