Output DACs with Internal Reference and I
參數資料
型號： MAX5815BAUD+T
廠商： Maxim Integrated Products
文件頁數： 7/30頁
文件大小： 0K
描述： IC DAC 12BIT SRL 4CH 14TSSOP
產品培訓模塊： Obsolescence Mitigation Program
標準包裝： 2,500
設置時間： 4.5µs
位數： 12
數據接口： I²C，串行
轉換器數目： 4
電壓電源： 模擬和數字
功率耗散（最大）： 797mW
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 帶卷 (TR)
輸出數目和類型： 4 電壓，單極
MAX5813/MAX5814/MAX5815
Ultra-Small, Quad-Channel, 8-/10-/12-Bit Buffered
Output DACs with Internal Reference and I2C Interface
15
Maxim Integrated
Clear Input (CLR)
The MAX5813/MAX5814/MAX5815 feature an asynchro-
nous active-low CLR logic input that simultaneously sets
all four DAC outputs to zero. Driving CLR low clears the
contents of both the CODE and DAC registers and also
aborts the on-going I2C command. To allow a new I2C
command, drive CLR high, satisfying the tCLRSTA timing
requirement.
Interface Power Supply (VDDIO)
The MAX5813/MAX5814/MAX5815 feature a separate
supply pin (VDDIO) for the digital interface (1.8V to 5.5V).
Connect VDDIO to the I/O supply of the host processor.
I2C Serial Interface
The MAX5813/MAX5814/MAX5815 feature an I2C-/
SMBusK-compatible, 2-wire serial interface consisting of
a serial data line (SDA) and a serial clock line (SCL). SDA
and SCL enable communication between the MAX5813/
MAX5814/MAX5815 and the master at clock rates up
to 400kHz. Figure 1 shows the 2-wire interface timing
diagram. The master generates SCL and initiates data
transfer on the bus. The master device writes data to the
MAX5813/MAX5814/MAX5815 by transmitting the proper
slave address followed by the command byte and then
the data word. Each transmit sequence is framed by a
START (S) or Repeated START (Sr) condition and a STOP
(P) condition. Each word transmitted to the MAX5813/
MAX5814/MAX5815 is 8 bits long and is followed by an
acknowledge clock pulse. A master reading data from
the MAX5813/MAX5814/MAX5815 must transmit the
proper slave address followed by a series of nine SCL
pulses for each byte of data requested. The MAX5813/
MAX5814/MAX5815 transmit data on SDA in sync with
the master-generated SCL pulses. The master acknowl-
edges receipt of each byte of data. Each read sequence
is framed by a START or Repeated START condition, a
not acknowledge, and a STOP condition. SDA operates
as both an input and an open-drain output. A pullup
resistor, typically 4.7kI is required on SDA. SCL oper-
ates only as an input. A pullup resistor, typically 4.7kI, is
required on SCL if there are multiple masters on the bus,
or if the single master has an open-drain SCL output.
Series resistors in line with SDA and SCL are optional.
Series resistors protect the digital inputs of the MAX5813/
MAX5814/MAX5815 from high voltage spikes on the bus
lines and minimize crosstalk and undershoot of the bus
signals. The MAX5813/MAX5814/MAX5815 can accom-
modate bus voltages higher than VDDIO up to a limit of
5.5V; bus voltages lower than VDDIO are not recommend-
ed and may result in significantly increased interface cur-
rents. The MAX5813/MAX5814/MAX5815 digital inputs
are double buffered. Depending on the command issued
through the serial interface, the CODE register(s) can
be loaded without affecting the DAC register(s) using
the write command. To update the DAC registers, either
drive the LDAC input low to asynchronously update all
DAC outputs, or use the software LOAD command.
I2C START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A mas-
ter initiates communication by issuing a START condition.
A START condition is a high-to-low transition on SDA with
SCL high. A STOP condition is a low-to-high transition
on SDA while SCL is high (Figure 2). A START condition
from the master signals the beginning of a transmission
Figure 2. I2C START, Repeated START, and STOP Conditions
SMBus is a trademark of Intel Corp.
Figure 2
SCL
SDA
SSrP
VALID START, REPEATED START, AND STOP PULSES
PS
P
SP
P
S
INVALID START/STOP PULSE PAIRINGS -ALL WILL BE RECOGNIZED AS STARTS
相關PDF資料
PDF描述
VE-BNP-MU-F1 CONVERTER MOD DC/DC 13.8V 200W
MAX522ESA+T IC DAC 8BIT DUAL SERIAL 8-SOIC
VE-BNN-MU-F4 CONVERTER MOD DC/DC 18.5V 200W
VE-B3D-MX-S CONVERTER MOD DC/DC 85V 75W
MAX5821MEUA+T IC DAC 10BIT DL 2WIRE SER 8-UMAX
相關代理商/技術參數
參數描述
MAX5815EVKIT# 制造商:Maxim Integrated Products 功能描述:EV KIT FOR MAX5815 12B 4 CHANNEL DAC WITH I2C INTERFACE - Boxed Product (Development Kits)
MAX5816ATB+ 功能描述:數模轉換器- DAC 12-Bit 4Ch V DAC w/I2C Interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5816ATB+T 功能描述:數模轉換器- DAC 12-Bit 4Ch V DAC w/I2C Interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5820LEUA 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5820LEUA+ 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*