- 您現在的位置：買賣IC網 > PDF目錄383443 > MAX5866 (Maxim Integrated Products, Inc.) Ultra-Low-Power. High-Dynamic-Performance. 60Msps Analog Front End PDF資料下載
參數資料
| 型號： | MAX5866 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Ultra-Low-Power. High-Dynamic-Performance. 60Msps Analog Front End |
| 中文描述： | 超低功耗、高動態性能、60Msps模擬前端 |
| 文件頁數： | 7/14頁 |
| 文件大小： | 382K |
| 代理商： | MAX5866 |
7) Verify that shunts are installed across jumpers JU10
and JU11 (CLKXP and CLKXN are not used for
evaluating the MAX5858A in PLL enabled mode).
8) Connect the TRIG OUTPUT (clock synchronize sig-
nal) of the HP 8131A to the clock input on the back
side of the data generator (Sony/Tektronix DG2020A).
(See Figure 2 for the equipment setup connections.)
9) Connect the OUTPUT signal of the HP 8131A to the
CLKIN SMA connector on the EV kit.
10) Verify that both the pulse generator and the data
generator are programmed for CMOS level outputs,
which transition from 0 to 3V.
11) Connect data generator POD A to the first variable
output POD (1). Connect output channels CH9
through CH0 of the variable output POD 1 to the
MAX5858A EV kit connector J1, as indicated in
Table 10.
12) Connect data generator POD B to the second vari-
able output POD (2). Connect output channels CH9
through CH0 of the variable output POD 2 to the
MAX5858A EV kit connector J1, as indicated in
Table 11.
13) Connect the spectrum analyzer to the OUTA or the
OUTB SMA connector.
14) Connect the 3V, 500mA power supply to DVDD.
Connect the ground terminal of this supply to
DGND.
15) Connect the 3V, 100mA power supply to AVDD.
Connect the ground terminal of this supply to
AGND.
16) Connect the 3V, 200mA power supply to PVDD.
Connect the ground terminal of this supply to PGND.
17) Turn on all three power supplies.
18) With a voltmeter, verify that 1.24V is measured at
the REFO pad on the EV kit.
19) Enable the pulse generator and the data generator.
For 1x interpolation, set the HP 8131A output for a
square wave with a frequency (f
CLK
) of
≤
165MHz.
For 2x interpolation, set the HP 8131A output for a
square wave with a frequency (f
CLK
) of
≤
150MHz.
For 4x interpolation, set the HP 8131A output for a
square wave with a frequency (f
CLK
) of
≤
75MHz.
20) Adjust the delay between the HP 8131A TRIG OUT-
PUT and signal OUTPUT to meet the MAX5858A
data timing specifications.
21) Use the spectrum analyzer to view the MAX5858A
output spectrum, or view the output waveforms
using an oscilloscope on the outputs.
E
MAX5858A Evaluation Kit
_______________________________________________________________________________________
7
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5885EVKIT | Evaluation Kit for the MAX5883/MAX5884/MAX5885 |
| MAX5888A | 3.3V.16-Bit.500Msps High Dynamic Performance DAC with Differential LVDS Inputs |
| MAX5888EVKIT | Evaluation Kit for the MAX5886/MAX5887/MAX5888 |
| MAX5895 | 16-Bit, 500Msps Interpolating and Modulating Dual DAC with CMOS Inputs |
| MAX5895EGK | 16-Bit, 500Msps Interpolating and Modulating Dual DAC with CMOS Inputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5866ETM | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5866ETM+ | 功能描述:ADC / DAC多通道 10-Bit 2Ch 60Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5866ETM+T | 功能描述:ADC / DAC多通道 10-Bit 2Ch 60Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5866ETM-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5868EXE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。