- 您現在的位置：買賣IC網 > PDF目錄11583 > MAX5941ACSE+ (Maxim Integrated Products)IC IEEE 802.3AF-COMP POE 16-SOIC PDF資料下載
參數資料
| 型號： | MAX5941ACSE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC IEEE 802.3AF-COMP POE 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 控制器類型： | 以太網供電控制器（POE） |
| 接口： | IEEE 802.3af |
| 電源電壓： | 48V |
| 電流 - 電源： | 1mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
MAX5941A/MAX5941B
IEEE 802.3af-Compliant Power-Over-Ethernet
Interface/PWM Controller for Power Devices
14
______________________________________________________________________________________
Thermal Dissipation
During classification mode, if the PSE applies the maxi-
mum DC voltage, the maximum voltage drop from GND
to VRCL will be 13V. If the maximum classification current
of 42mA flows through the MAX5941A/MAX5941B, then
the maximum DC power dissipation will be close to
546mW, which is slightly higher than the maximum DC
power dissipation of the IC at maximum operating tem-
perature. However, according to the IEEE 802.3af stan-
dard, the duration of the classification mode is limited to
75ms (max). The MAX5941A/MAX5941B handles the
maximum classification power dissipation for the maxi-
mum duration time without sustaining any internal dam-
age. If the PSE violates the IEEE 802.3af standard by
exceeding the 75ms maximum classification duration, it
may cause internal damage to the IC.
PWM Controller
Current-Mode Control
The MAX5941A/MAX5941B offer current-mode control
operation with added features such as leading-edge
blanking with dual internal path that only blanks the
sensed current signal applied to the input of the PWM
comparator. The current-limit comparator monitors the
CS pin at all times and provides cycle-by-cycle current
limit without being blanked. The leading-edge blanking
of the CS signal prevents the PWM comparator from
prematurely terminating the on cycle. The CS signal
contains a leading-edge spike that is the result of the
MOSFET gate charge current, capacitive and diode
reverse recovery current of the power circuit. Since this
leading-edge spike is normally lower than the current
limit comparator threshold, current limiting is not
blanked and cycle-by-cycle current limiting is provided
under all conditions.
Use the MAX5941A in discontinuous flyback applica-
tions where wide line voltage and load current variation
is expected. Use the MAX5941B for single transistor
forward converters where the maximum duty cycle must
be limited to less than 50%.
Under certain conditions, it may be advantageous to
use a forward converter with greater than 50% duty
cycle. For those cases, use the MAX5941A. The large
duty cycle results in much lower operating primary RMS
currents through the MOSFET switch and in most cases
a smaller output filter inductor. The major disadvantage
to this is that the MOSFET voltage rating must be higher
and that slope compensation must be provided to sta-
bilize the inner current loop. The MAX5941A provides
internal slope compensation.
Optocoupled Feedback
Isolated voltage feedback is achieved by using an opto-
coupler and a shunt regulator as shown in Figure 5. The
output voltage set-point accuracy is a function of the
accuracy of the shunt regulator and feedback resistor-
divider tolerance.
Internal Regulators
The internal regulators of the MAX5941A/MAX5941B
enable initial startup without a lossy startup resistor and
regulate the voltage at the output of a tertiary (bias) wind-
ing to provide power for the IC. At startup, V+ is regulat-
ed down to VCC to provide bias for the device. The VDD
regulator then regulates from the output of the tertiary
winding to VCC. This architecture allows the tertiary wind-
ing to have only a small filter capacitor at its output thus
eliminating the additional cost of a filter inductor.
When designing the tertiary winding, calculate the num-
ber of turns so the minimum reflected voltage is always
higher than 12.7V. The maximum reflected voltage must
be less than 36V.
To reduce power dissipation, the high-voltage regulator
is disabled when the VDD voltage reaches 12.7V. This
greatly reduces power dissipation and improves effi-
ciency. If VCC falls below the undervoltage lockout
threshold (VCC = 6.6V), the low-voltage regulator is dis-
abled, and soft-start is reinitiated. In undervoltage lock-
out the MOSFET driver output (NDRV) is held low.
If the input voltage range is between 13V and 36V, V+
and VDD may be connected to the line voltage provided
that the maximum power dissipation is not exceeded.
This eliminates the need for a tertiary winding.
PWM Controller Undervoltage Lockout,
Soft-Start, and Shutdown
The soft-start feature of the MAX5941A/MAX5941B
allows the load voltage to ramp up in a controlled man-
ner, thus eliminating output voltage overshoot.
While the controller is in undervoltage lockout, the
capacitor connected to the SS_SHDN pin is dis-
charged. Upon coming out of undervoltage lockout, an
internal current source starts charging the capacitor to
initiate the soft-start cycle. Use the following equation to
calculate total soft-start time:
where CSS is the soft-start capacitor as shown in Figure 5.
Operation begins when VSS_SHDN ramps above 0.6V.
When soft-start has completed, VSS_SHDN is regulated
t
ms
C
startup
ss
=×
045
.
nF
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF1829-E/SO | MCU PIC 14KB FLASH 20-SOIC |
| PIC16F1829-E/SO | MCU PIC 14K FLASH 1K RAM 20SOIC |
| 73S8014RN-IL/F | IC SMART CARD 7816 EMV 20-SOIC |
| PIC16F687T-I/ML | IC PIC MCU FLASH 2KX14 20QFN |
| PIC16F687T-I/SO | IC PIC MCU FLASH 2KX14 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5941ACSE+ | 功能描述:輸入/輸出控制器接口集成電路 IEEE 802.3af POE Int/PWM Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX5941ACSE+T | 功能描述:輸入/輸出控制器接口集成電路 IEEE 802.3af POE Int/PWM Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX5941ACSE-T | 功能描述:電源開關 IC - POE / LAN RoHS:否 制造商:Fairchild Semiconductor 開關數量:Single 開關配置:SPST 開啟電阻（最大值）:7.3 Ohms 串話: 帶寬: 開啟時間（最大值）:13 ns 關閉時間（最大值）:20 ns 切換電壓（最大）: 工作電源電壓:8 V to 26 V 最大工作溫度:+ 125 C 安裝風格:Through Hole 封裝 / 箱體:TO-220F-6 |
| MAX5941AESE | 功能描述:電源開關 IC - POE / LAN RoHS:否 制造商:Fairchild Semiconductor 開關數量:Single 開關配置:SPST 開啟電阻（最大值）:7.3 Ohms 串話: 帶寬: 開啟時間（最大值）:13 ns 關閉時間（最大值）:20 ns 切換電壓（最大）: 工作電源電壓:8 V to 26 V 最大工作溫度:+ 125 C 安裝風格:Through Hole 封裝 / 箱體:TO-220F-6 |
| MAX5941AESE+ | 功能描述:輸入/輸出控制器接口集成電路 IEEE 802.3af POE Int/PWM Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。