- 您現在的位置：買賣IC網 > PDF目錄383451 > MAX6373KA-T (MAXIM INTEGRATED PRODUCTS INC) Pin-Selectable Watchdog Timers PDF資料下載
參數資料
| 型號： | MAX6373KA-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Pin-Selectable Watchdog Timers |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | SOT-23, 8 PIN |
| 文件頁數： | 8/8頁 |
| 文件大?。?/td> | 114K |
| 代理商： | MAX6373KA-T |
M
Pin-Selectable Watchdog Timers
Selecting 011 (SET2 = 0, SET1 = 1, SET0 = 1) disables
the watchdog timer function on all devices in the family.
Operation can be reenabled without powering down by
changing the set inputs to the new desired setting. The
device assumes the new selected timing characteris-
tics and enter the startup phase after the 300μs setup
time elapses (Figure 3).
The MAX6373/MAX6374 offer a first-edge feature. In
first-edge mode (settings 101 or 110, Table 1), the
internal timer does not control the startup delay period.
Instead, startup terminates when WDI sees a transition.
If changing to first-edge mode while the device is oper-
ating, disable mode must be entered first. It is then safe
to select first-edge mode. Entering disable mode first
ensures the output is unasserted when selecting first-
edge mode and removes the danger of WDI being
masked out.
Output
The MAX6369/MAX6371/MAX6373 have an active-low,
open-drain output that provides a watchdog output
pulse of 100ms. This output structure sinks current
when
WDO
is asserted. Connect a pullup resistor from
WDO
to any supply voltage up to +5.5V.
Select a resistor value large enough to register a logic
low (see
Electrical Characteristics
), and small enough
to register a logic high while supplying all input current
and leakage paths connected to the
WDO
line. A 10k
pullup is sufficient in most applications. The MAX6370/
MAX6372/MAX6374 have push-pull outputs that pro-
vide an active-low watchdog output pulse of 1ms.
When
WDO
deasserts, timing begins again at the
beginning of the watchdog timeout period (Figure 2).
Usage in Noisy Environments
If using the watchdog timer in an electrically noisy envi-
ronment, a bypass capacitor of 0.1μF should be con-
nected between V
CC
and GND as close to the device
as possible, and no further away than 0.2 inches.
________________Watchdog Software
Considerations
To help the watchdog timer monitor software execution
more closely, set and reset the watchdog input at differ-
ent points in the program, rather than pulsing the watch-
dog input high-low-high or low-high-low. This technique
avoids a stuck loop, in which the watchdog timer would
continue to be reset inside the loop, keeping the watch-
dog from timing out. Figure 4 shows an example of a
flow diagram where the I/O driving the watchdog input is
set high at the beginning of the program, set low at the
end of every subroutine or loop, then set high again
when the program returns to the beginning. If the pro-
gram should hang in any subroutine, the problem would
be quickly corrected, since the I/O is continually set low
and the watchdog timer is allowed to time out, causing
WDO
to pulse.
START
SET WDI
HIGH
PROGRAM
CODE
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
RETURN
POSSIBLE
INFINITE LOOP PATH
Figure 4. Watchdog Flow Diagram
Chip Information
TRANSISTOR COUNT: 1500
PROCESS: BiCMOS
SET2
SET1
SET0
1
2
8
7
V
CC
WDO
GND
N.C.
WDI
SOT23-8
TOP VIEW
3
4
6
5
MAX6369
MAX6370
MAX6371
MAX6372
MAX6373
MAX6374
Pin Configuration
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6369KA-T | Pin-Selectable Watchdog Timers |
| MAX6399 | High-Voltage, Overvoltage/Undervoltage, Protection Switch Controller |
| MAX6399ATA-T | High-Voltage, Overvoltage/Undervoltage, Protection Switch Controller |
| MAX6400BS27-T | Analog IC |
| MAX6400-MAX6405 | レP Supervisory Circuits in 4-Bump (2 x 2) Chip-Scale Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6374KA | 制造商:Maxim Integrated Products 功能描述:8-SOT_ - Rail/Tube |
| MAX6374KA/V+T | 功能描述:計時器和支持產品 Pin-Selectable Watchdog Timer RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX6374KA+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 8UA 8PIN SOT-23 - Rail/Tube |
| MAX6374KA+T | 功能描述:監控電路 Pin-Selectable Watchdog Timer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6374KA-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。