- 您現在的位置：買賣IC網 > PDF目錄5334 > MAX6496ATA+T (Maxim Integrated Products)IC CTLR PROT SW 8-TDFN PDF資料下載
參數資料
| 型號： | MAX6496ATA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR PROT SW 8-TDFN |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 電壓 - 工作： | 72V |
| 技術： | 混合技術 |
| 功率（瓦特）： | 1.45W |
| 電路數： | 1 |
| 應用： | 通用 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN-EP（3x3） |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX6496ATA+TDKR |
MAX6495–MAX6499
72V, Overvoltage-Protection Switches/
Limiter Controllers with an External MOSFET
9
Maxim Integrated
Power-OK Output (MAX6497/MAX6498)
POK is an open-drain output that remains low when the
voltage at POKSET is below the internal POKSET
threshold (1.18V). POK goes high impedance when
POKSET goes above the internal POKSET threshold
(1.24V). Connect a resistive divider from OUTFB to
POKSET to adjust the desired undervoltage threshold.
Use a resistor in the 100kΩ range from POKSET to
GND to minimize current consumption.
Overvoltage Latch Function
The MAX6497/MAX6499 offers a latch function that pre-
vents the external MOSFET from turning on until the
latch is cleared. For the MAX6497, the latch can be
cleared by cycling the power on the input IN to a volt-
age below the undervoltage lockout or by pulling the
shutdown input low and then back to a logic-high
state. The MAX6499 offers a
CLEAR input that latches
the n-MOSFET off when
CLEAR is high. The latch is
removed when the
CLEAR input is plused low. Connect
CLEAR low to make the latch transparent.
Overvoltage Retry Function
The MAX6498 offers an automatic retry function that
tries to enhance the external n-channel MOSFET after
the overvoltage condition is removed. When the monitored
input voltage detects an overvoltage condition (VSET >
VTH+), the n-MOSFET is turned off. The MOSFET stays off
until the voltage at VSET falls below its VTH- (typically
0.13V), at which point the output tries to turn on again.
Applications Information
Load Dump
Most automotive applications run off a multicell “12V”
lead-acid battery with a nominal voltage that swings
between 9V and 16V (depending on load current,
charging status, temperature, battery age, etc.). The
battery voltage is distributed throughout the automobile
and is locally regulated down to voltages required by
the different system modules. Load dump occurs when
the alternator is charging the battery and the battery
becomes disconnected. The alternator voltage regula-
tor is temporarily driven out of control. Power from the
alternator flows into the distributed power system and
elevates the voltage seen at each module. The voltage
spikes have rise times typically greater than 5ms and
decays within several hundred milliseconds but can
extend out to 1s or more depending on the characteris-
tics of the charging system. These transients are capa-
ble of destroying sensitive electronic equipment on the
first “fault event.”
Setting Overvoltage Thresholds
OVSET provides an accurate means to set the overvolt-
age level for the MAX6495–MAX6499. Use a resistive
divider to set the desired overvoltage condition (see
Figure 2). OVSET has a rising 1.24V threshold with a
5% falling hysteresis (MAX6495/MAX6496/MAX6499)
and a rising 0.505V threshold with a falling 0.15V
threshold (MAX6497/MAX6498).
Begin by selecting the total end-to-end resistance, RTO-
TAL = R1 + R2. Choose RTOTAL to yield a total current
equivalent to a minimum 100 x ISET (OVSET’s input bias
current) at the desired overvoltage threshold.
For example:
With an overvoltage threshold (VOV) set to 20V for the
MAX6495/MAX6496/MAX6499, RTOTAL < 20V / (100 x
ISET), where ISET is OVSET’s 50nA (max) input bias current.
RTOTAL < 4MΩ
Use the following formula to calculate R2:
where VTH+ is the 1.24V OVSET rising threshold and
VOV is the desired overvoltage threshold.
R2 = 248kΩ. Use a 249kΩ standard resistor.
RTOTAL = R2 + R1, where R1 = 3.751MΩ. Use a
3.74MΩ standard resistor.
A lower value for total resistance dissipates more power
but provides slightly better accuracy. To improve ESD
protection, keep R2 ≥ 1kΩ.
Reverse-Battery Protection
The MAX6496 is an overvoltage-protection circuit that is
capable of driving a p-channel MOSFET to prevent
reverse-battery conditions. This MOSFET eliminates the
need for external diodes, thus minimizing the input volt-
age drop (see Figure 8).
Inrush/Slew-Rate Control
Inrush current control can be implemented by placing a
capacitor from GATE to GND to slowly ramp up the
GATE, thus limiting the inrush current and controlling
GATE’s slew rate during initial turn-on. The inrush cur-
rent can be approximated using the following equation:
I
C
II
INRUSH
OUT
GATE
LOAD
=×
+
RV
R
V
TH
TOTAL
OV
2
=×
+
相關PDF資料 |
PDF描述 |
|---|---|
| LTC6240HVHS5#TRMPBF | IC OP AMP SINGLE R-R TSOT23-5 |
| 0034.6921 | FUSE 4A 250V 8.5X8.5 T 4.3 |
| EL5300IU | IC AMP V-FB TRPL 200MHZ 16-QSOP |
| MAX6499ATA+T | IC CTLR PROT SW 8-TDFN |
| LTC6240HVIS5#TRMPBF | IC OP AMP SINGLE R-R TSOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6496EVKIT+ | 功能描述:電源管理IC開發工具 MAX6496 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX6497ATA+ | 制造商:Maxim Integrated Products 功能描述:OVERVOLT PROT CNTRLR 8TDFN EP - Rail/Tube |
| MAX6497ATA+T | 功能描述:電流和電力監控器、調節器 72V Over V Protect Switch/Limiter RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX6498ATA+ | 制造商:Maxim Integrated Products 功能描述:OVERVOLT PROT CNTRLR 8TDFN EP - Rail/Tube |
| MAX6498ATA+T | 功能描述:電流和電力監控器、調節器 72V Over V Protect Switch/Limiter RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。