- 您現在的位置：買賣IC網 > PDF目錄67800 > MAX6615AEE+ (MAXIM INTEGRATED PRODUCTS INC) Dual-Channel Temperature Monitors and Fan-Speed Controllers with Thermistor Inputs PDF資料下載
參數資料
| 型號： | MAX6615AEE+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Dual-Channel Temperature Monitors and Fan-Speed Controllers with Thermistor Inputs |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, 0.635 MM PITCH, MO-137-AB, QSOP-16 |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 186K |
| 代理商： | MAX6615AEE+ |
brushless DC motor has enough time to operate. When
driving a fan with a PWM-to-DC circuit as shown in
Figure 5, the highest available frequency (35kHz) should
be used to minimize the size of the filter capacitors.
When using a fan with a PWM control input, the frequen-
cy normally should be high as well, although some fans
have PWM inputs that accept low-frequency drive.
The duty cycle of the PWM can be controlled in two ways:
1) Manual PWM control: setting the duty cycle of the fan
directly through the fan target duty-cycle registers
(0Bh and 0Ch).
2) Automatic PWM control: setting the duty cycle based
on temperature.
Manual PWM Duty-Cycle Control
Clearing the bits that select the temperature channels for
fan control (D5 and D4 for PWM1 and D3 and D2 for
PWM2) in the fan-configuration register (11h) enables
manual fan control. In this mode, the duty cycle written to
the fan target duty-cycle register directly controls the
corresponding fan. The value is clipped to a maximum of
240. Any value entered above that is changed to 240
automatically. In this control mode, the value in the maxi-
mum duty-cycle register is ignored and does not affect
the duty cycle used to control the fan.
Automatic PWM Duty-Cycle Control
In the automatic control mode, the duty cycle is con-
trolled by the local or remote temperature according to
the settings in the control registers. Below the fan-start
temperature, the duty cycle is either 0% or is equal to
the fan-start duty cycle, depending on the value of bit
D3 in the configuration byte register. Above the fan-
start temperature, the duty cycle increases by one
duty-cycle step each time the temperature increases by
one temperature step. The target duty cycle is calculat-
ed based on the following formula; for temperature >
FanStartTemperature:
where:
DC = DutyCycle
FSDC = FanStartDutyCycle
T = Temperature
FST = FanStartTemperature
DCSS = DutyCycleStepSize
TS = TempStep
Duty cycle is recalculated after each temperature con-
version if temperature is increasing. If the temperature
begins to decrease, the duty cycle is not recalculated
until the temperature drops by 5°C from the last peak
temperature. The duty cycle remains the same until the
temperature drops 5°C from the last peak temperature or
the temperature rises above the last peak temperature.
For example, if the temperature goes up to +85°C and
starts decreasing, duty cycle is not recalculated until the
temperature reaches +80°C or the temperature rises
above +85°C. If the temperature decreases further, the
duty cycle is not updated until it reaches +75°C.
For temperature < FanStartTemperature and D2 of
configuration register = 0:
DutyCycle = 0
For temperature < FanStartTemperature and D2 of
configuration register = 1:
DutyCycle = FanStartDutyCycle
Once the temperature crosses the fan-start temperature
threshold, the temperature has to drop below the fan-
start temperature threshold minus the hysteresis before
DC
FSDC
T
FST
DCSS
TS
=+
×
(
)
-
MAX6615/MAX6616
Dual-Channel Temperature Monitors and
Fan-Speed Controllers with Thermistor Inputs
_______________________________________________________________________________________
9
+3.3V
PWM
18k
27k
10k
120k
+3.3V
+12V
500k
VOUT
TO FAN
1
F
1
F
0.01
F
0.1
F
Figure 5. Driving a Fan with a PWM-to-DC Circuit
VCC
PWM
4.7k
5V
Figure 6. Controlling a PWM Input Fan with the MAX6615/
MAX6616s’ PWM Output (Typically, the 35kHz PWM
Frequency Is Used)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6625PMTT+T | 9-Bit/12-Bit Temperature Sensors with I<sup>2</sup>C-Compatible Serial Interface in a SOT23 |
| MAX6626PMTT+ | 9-Bit/12-Bit Temperature Sensors with I<sup>2</sup>C-Compatible Serial Interface in a SOT23 |
| MAX6626RMTT+ | 9-Bit/12-Bit Temperature Sensors with I<sup>2</sup>C-Compatible Serial Interface in a SOT23 |
| MAX6633MSA+ | 12-Bit Plus Sign Temperature Sensors with SMBus/I<sup>2</sup>C-Compatible Serial Interface |
| MAX6633MSA+T | 12-Bit Plus Sign Temperature Sensors with SMBus/I<sup>2</sup>C-Compatible Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6615AEE+ | 功能描述:板上安裝溫度傳感器 Dual Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6615AEE+T | 功能描述:板上安裝溫度傳感器 Dual Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6615AEE-T | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6616AEG | 功能描述:板上安裝溫度傳感器 Dual Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6616AEG+ | 功能描述:板上安裝溫度傳感器 Dual Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。