- 您現在的位置：買賣IC網 > PDF目錄67800 > MAX6635MSA+ (MAXIM INTEGRATED PRODUCTS INC) 12-Bit Plus Sign Temperature Sensors with SMBus/I<sup>2</sup>C-Compatible Serial Interface PDF資料下載
參數資料
| 型號： | MAX6635MSA+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 12-Bit Plus Sign Temperature Sensors with SMBus/I<sup>2</sup>C-Compatible Serial Interface |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 210K |
| 代理商： | MAX6635MSA+ |
Temperature Alert
(MAX6634/MAX6635)
ALERT has programmable polarity and two modes:
comparator and interrupt. Polarity and mode are select-
ed through the Configuration register (Table 4). The
ALERT output is open drain.
Interrupt Mode
With ALERT in interrupt mode, the MAX6634/MAX6635
look for a THIGH or a TLOW fault. The ALERT pin asserts
an alarm for an undertemperature fault, as well as for
an overtemperature fault. Once either fault has
occurred, it remains active until deasserted by a read
of any register. The device then begins to look for a
temperature change crossing the hysteresis level. The
activation of ALERT is subject to the depth of the fault
queue.
For example: If THIGH is set to 100°C, THYST is set to
20°C, and the fault queue depth is set to 4, ALERT
does not assert until four consecutive conversions
exceed 100°C. If the temperature is then read through
the I2C-compatible interface, ALERT deasserts. ALERT
asserts again when four consecutive conversions are
less than 80°C.
Comparator Mode
In comparator mode, ALERT is asserted when the num-
ber of consecutive conversions exceeding the value in
the THIGH register, or lower than the value in the TLOW
register, is equal to the depth of the fault queue. ALERT
deasserts when the number of consecutive conversions
less than THIGH - THYST or greater than TLOW + THYST
is equal to the depth of the fault queue.
For example: If THIGH is set to 100°C, TLOW is set to
80°C, and the fault queue depth is set to four, ALERT
does not assert until four consecutive conversions
exceed 100°C, or are below 80°C. ALERT only
deasserts if four consecutive conversions are less than
THIGH - THYST or greater than TLOW + THYST.
Comparator mode allows autonomous clearing of an
ALERT fault without the intervention of a master and is
ideal to use for driving a thermostat (Figure 10).
Overtemperature Alarm (MAX6635)
The MAX6635 also includes an overtemperature output
that is always in comparator mode. Whenever the tem-
perature exceeds a value in the programmable TMAX
register, OVERT is asserted. OVERT only deasserts
after the temperature drops below TMAX - THYST. When
the fault queue is activated, OVERT is subject to that
queue, which sets the number of faults that must occur
before OVERT asserts or deasserts. This helps prevent
spurious alarms in noisy environments.
Comparator mode also allows autonomous clearing of
an OVERT fault without the intervention of a master and
thus is ideal to use for driving a cooling fan (Figure 11).
In this application, the polarity of OVERT is active high.
Shutdown
The MAX6633/MAX6634/MAX6635 feature a shutdown
mode, accessible through the serial interface that
saves power by turning off everything except the POR
MAX6633/MAX6634/MAX6635
12-Bit Plus Sign Temperature Sensors with
SMBus/I2C-Compatible Serial Interface
______________________________________________________________________________________
11
3
8
VCC
+3V TO +5.5V
MAX6634
RELAY
5VDC, 20mA
125VAC, 1A
2N3904
HEATER
SUPPLY
HEATER
4
4k
ALERT
Figure 10. Simple Thermostat
3
10k
8
VCC
+3V TO +5.5V
+12V
MAX6635
4
12V 300mA
MOTOR
FAN
LOGIC-LEVEL
MOSFET
OVERT
Figure 11. Fan Controller
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6635MSA+T | 12-Bit Plus Sign Temperature Sensors with SMBus/I<sup>2</sup>C-Compatible Serial Interface |
| MAX6639AEE+T | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639ATE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639ATE+T | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639YAEE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6635MSA+ | 功能描述:板上安裝溫度傳感器 12-Bit + Sign Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6635MSA+T | 功能描述:板上安裝溫度傳感器 12-Bit + Sign Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6635MSA-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6636UP9A+ | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6636UP9A+T | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。