參數資料
型號： MAX6640YAEE+
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller
中文描述： SPECIALTY ANALOG CIRCUIT, PDSO16
封裝： 0.150 INCH, 0.025 INCH PITCH, ROHS COMPLIANT, MO-137AB, QSOP-16
文件頁數： 11/24頁
文件大小： 428K
代理商： MAX6640YAEE+
The transistor must be a small-signal type with a rela-
tively high forward voltage; otherwise, the ADC input
voltage range can be violated. The forward voltage at
the highest expected temperature must be greater than
0.25V at 10A, and at the lowest expected tempera-
ture, the forward voltage must be less than 0.95V at
100A. Large-power transistors must not be used. Also,
ensure that the base resistance is less than 100. Tight
specifications for forward current gain (50 < < 150,
for example) indicate that the manufacturer has good
process controls and that the devices have consistent
VBE characteristics.
ADC Noise Filtering
The integrating ADC has inherently good noise rejec-
tion, especially of low-frequency signals such as
60Hz/120Hz power-supply hum. Micropower operation
places constraints on high-frequency noise rejection.
Lay out the PC board carefully with proper external
noise filtering for high-accuracy remote measurements
in electrically noisy environments.
Filter high-frequency electromagnetic interference
(EMI) at DXP and DXN with an external 2200pF capaci-
tor connected between the two inputs. This capacitor
can be increased to about 3300pF (max), including
cable capacitance. A capacitance higher than 3300pF
introduces errors due to the rise time of the switched-
current source.
Twisted Pairs and Shielded Cables
For remote-sensor distances longer than 8in, or in par-
ticularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6ft to 12ft (typ) before
noise becomes a problem, as tested in a noisy elec-
tronics laboratory. For longer distances, the best solu-
tion is a shielded twisted pair like that used for audio
microphones. For example, Belden #8451 works well
for distances up to 100ft in a noisy environment.
Connect the twisted pair to DXP and DXN and the
shield to ground, and leave the shield’s remote end
unterminated. Excess capacitance at DXN or DXP limits
practical remote-sensor distances (see the Typical
Operating Characteristics).
For very long cable runs, the cable’s parasitic capaci-
tance often provides noise filtering, so the recommend-
ed 2200pF capacitor can often be removed or reduced
in value. Cable resistance also affects remote-sensor
accuracy. A 1 series resistance introduces about
+1/2°C error.
PC Board Layout Checklist
1) Place the MAX6640 as close as practical to the
remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 4in to
8in, or more, as long as the worst noise sources
(such as CRTs, clock generators, memory buses,
and ISA/PCI buses) are avoided.
2) Do not route the DXP/DXN lines next to the deflection
coils of a CRT. Also, do not route the traces across a
fast memory bus, which can easily introduce +30°C
error, even with good filtering. Otherwise, most noise
sources are fairly benign.
3) Route the DXP and DXN traces parallel and close to
each other, away from any high-voltage traces such
as +12VDC. Avoid leakage currents from PC board
contamination. A 20M leakage path from DXP
ground causes approximately +1°C error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces. With guard traces, placing routing
near high-voltage traces is no longer an issue.
5) Route as few vias and crossunders as possible to
minimize copper/solder thermocouple effects.
6) When introducing a thermocouple, make sure that
both the DXP and the DXN paths have matching
thermocouples. In general, PC board-induced ther-
mocouples are not a serious problem. A copper
solder thermocouple exhibits 3V/°C, and it takes
approximately 200V of voltage error at DXP/DXN
to cause a +1°C measurement error, so most para-
sitic thermocouple errors are swamped out.
7) Use wide traces. Narrow traces are more inductive
and tend to pick up radiated noise. The 10-mil widths
and spacings recommended are not absolutely nec-
essary (as they offer only a minor improvement in
leakage and noise), but use them where practical.
8) Placing an electrically clean copper ground plane
between the DXP/DXN traces and traces carrying
high-frequency noise signals helps reduce EMI.
MAX6640
2-Channel Temperature Monitor with Dual
Automatic PWM Fan-Speed Controller
______________________________________________________________________________________
19
相關PDF資料
PDF描述
MAX6640YAEE+T 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller
MAX6640AEE+ 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller
MAX6641AUB90+ SMBus-Compatible Temperature Monitor with Automatic PWM Fan-Speed Controller
MAX6641AUB90+T SMBus-Compatible Temperature Monitor with Automatic PWM Fan-Speed Controller
MAX6641AUB92+ SMBus-Compatible Temperature Monitor with Automatic PWM Fan-Speed Controller
相關代理商/技術參數
參數描述
MAX6640YAEE+ 功能描述:板上安裝溫度傳感器 Sensors, Transducers RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6640YAEE+T 功能描述:板上安裝溫度傳感器 Sensors, Transducers RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6641AUB90 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6641AUB90+ 功能描述:板上安裝溫度傳感器 SMBus-Compatible Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6641AUB90+T 功能描述:板上安裝溫度傳感器 SMBus-Compatible Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*