- 您現在的位置：買賣IC網 > PDF目錄67801 > MAX6683AUB+ (MAXIM INTEGRATED PRODUCTS INC) Temperature Sensor and System Monitor in a 10-Pin µMAX PDF資料下載
參數資料
| 型號： | MAX6683AUB+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Temperature Sensor and System Monitor in a 10-Pin µMAX |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | MICRO MAX PACKAGE-10 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 230K |
| 代理商： | MAX6683AUB+ |
MAX6683
The POR state of the THOT register is 0101 0000 or
+80°C. The POR state of the THYST register is 0100
0001 or +65°C.
High and low limits for the voltage inputs are stored in
registers 2Bh through 32h. If a measured voltage is less
than VLOW or greater than VHIGH, an ALERT is asserted.
The POR states of the high and low voltage limits are
1.1 and 0.9 times the nominal voltage for each input.
Interrupt Status Byte Functions
The Interrupt Status Register records temperature or
voltage fault conditions whenever a limit is exceeded
(Table 5). Bits 0 through 3 correspond to the 2.5V, 1.8V,
5V, and VCC voltage inputs and bit 4 corresponds to
the temperature. If a threshold has been crossed, the
appropriate bit contains a 1. In the default and one-time
interrupt modes, reading the status register clears the
register until a new out-of-range condition is detected.
Temperature Sensor and System Monitor
in a 10-Pin MAX
8
_______________________________________________________________________________________
Table 4. Configuration Register (Address 40h, Power-On Default = 08h)
BIT
NAME
READ/WRITE
DESCRIPTION
0
Start/Stop
R/W
This bit controls the monitoring loop. Setting the bit to zero stops the
monitoring loop and puts the device into shutdown mode. The I
2C/SMBus
interface is still active during the shutdown mode. Setting the bit to 1 starts the
monitoring cycle. All high/low limits should be set before setting this bit to 1.
1
ALERT Enable
R/W
This bit is used to enable or disable the ALERT output. Setting the bit to 1
enables the ALERT output; setting the bit to 0 disables the ALERT output.
2
Reserved
——
3
ALERT Clear
R/W
This bit is used to clear the ALERT output when it is set to high. It does not
affect the Interrupt Status Register. The monitoring loop does not start until the
bit is set to zero.
4
Line Frequency
Select
R/W
This bit controls the internal clock frequency. Setting the bit to 1 changes the
clock frequency to 51.2kHz from 61.4kHz. This can improve the measurement
accuracy when the power-line frequency is at 50Hz.
5
Short Cycle
R/W
This bit reduces the conversion time by a factor of 4 when it is set to 1.
6
Reserved
——
7
Reset
R/W
This bit is used as a reset signal for the register initialization. The 1 of this bit
resets all the register values into the power-up default mode, including bit 7
itself.
Table 5. Interrupt Status Register (Address 41h, Power-Up Default = 00h)
BIT
NAME
READ/WRITE
DESCRIPTION
0
2.5VIN-Error
R
A 1 indicates either a high or low limit has been exceeded at the 2.5VIN input.
1
1.8VIN-Error
R
A 1 indicates either a high or low limit has been exceeded at the 1.8VIN input.
25VIN-Error
R
A 1 indicates either a high or low limit has been exceeded at the 5VIN input.
3VCC-Error
R
A 1 indicates either a high or low limit has been exceeded at the VCC input.
4
Temp-Error
R
A 1 indicates either a high or low limit has been exceeded at the internal
temperature sensor. The conditions that generate and clear this bit depend
on the temperature interrupt mode selected by bits 0 and 1 in the
Temperature Configuration Register.
5, 6, 7
Reserved
——
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6683AUB+T | Temperature Sensor and System Monitor in a 10-Pin µMAX |
| MAX6688AU75H+T | Local/Remote Temperature Switches in a µMAX Package |
| MAX6688AU75L+T | Local/Remote Temperature Switches in a µMAX Package |
| MAX6689UP9A+T | 7-Channel Precision Temperature Monitor |
| MAX668EUB+ | 1.8V to 28V Input, PWM Step-Up Controllers in µMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6683AUB+ | 功能描述:板上安裝溫度傳感器 Temperature Sensor & System Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6683AUB+T | 功能描述:板上安裝溫度傳感器 Temperature Sensor & System Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6683AUB-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6683EVKIT | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6683EVSYS | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。