- 您現在的位置：買賣IC網 > PDF目錄385542 > MAX6699EE (MAXIM INTEGRATED PRODUCTS INC) 5-Channel Precision Temperature Monitor PDF資料下載
參數資料
| 型號： | MAX6699EE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 5-Channel Precision Temperature Monitor |
| 中文描述： | ANALOG TEMP SENSOR-VOLTAGE, 0.3-3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, 0.025 PITCH, MO-153, QSOP-16 |
| 文件頁數： | 16/19頁 |
| 文件大小： | 321K |
| 代理商： | MAX6699EE |
M
ADC Noise Filtering
The integrating ADC has good noise rejection for low-
frequency signals, such as power-supply hum. In envi-
ronments with significant high-frequency EMI, connect
an external 2200pF capacitor between DXP_ and
DXN_. Larger capacitor values can be used for added
filtering, but do not exceed 3300pF because it can
introduce errors due to the rise time of the switched
current source. High-frequency noise reduction is
needed for high-accuracy remote measurements.
Noise can be reduced with careful PC board layout as
discussed in the
PC Board Layout
section.
Slave Address
Table 11 shows the MAX6699 slave address.
PC Board Layout
Follow these guidelines to reduce the measurement
error when measuring remote temperature:
1) Place the MAX6699 as close as is practical to the
remote diode. In noisy environments, such as a
computer motherboard, this distance can be 4in to
8in (typ). This length can be increased if the worst
noise sources are avoided. Noise sources include
CRTs, clock generators, memory buses, and PCI
buses.
2) Do not route the DXP-DXN lines next to the deflec-
tion coils of a CRT. Also, do not route the traces
across fast digital signals, which can easily intro-
duce +30°C error, even with good filtering.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other. Each parallel pair of
traces should go to a remote diode. Route these
traces away from any higher voltage traces, such as
+12VDC. Leakage currents from PC board contami-
nation must be dealt with carefully since a 20M
leakage path from DXP to ground causes about
+1°C error. If high-voltage traces are unavoidable,
connect guard traces to GND on either side of the
DXP-DXN traces (Figure 5).
4) Route through as few vias and crossunders as pos-
sible to minimize copper/solder thermocouple
effects.
5) Use wide traces when practical.
6) When the power supply is noisy, add a resistor (up
to 47
) in series with V
CC
.
Twisted-Pair and Shielded Cables
Use a twisted-pair cable to connect the remote sensor
for remote-sensor distances longer than 8in or in very
noisy environments. Twisted-pair cable lengths can be
between 6ft and 12ft before noise introduces excessive
errors. For longer distances, the best solution is a
shielded twisted pair like that used for audio micro-
phones. For example, Belden #8451 works well for dis-
tances up to 100ft in a noisy environment. At the
device, connect the twisted pair to DXP and DXN and
the shield to GND. Leave the shield unconnected at the
5-Channel Precision Temperature Monitor
16
______________________________________________________________________________________
5 mils
5 mils
5 mils
MINIMUM
5 mils
GND
DXP
DXN
GND
Figure 5. Recommended Minimum DXP-DXN PC Board Traces.
MANUFACTURER
Central Semiconductor (USA)
Rohm Semiconductor (USA)
Samsung (Korea)
Siemens (Germany)
Zetex (England)
MODEL NO.
CMPT3904
SST3904
KST3904-TF
SMBT3904
FMMT3904CT-ND
Table 10. Remote-Sensors Transistor
Manufacturers
Note:
Discrete transistors must be diode connected (base
shorted to collector).
PART
SMBus SLAVE ID
0011 010
0011 100
1001 100
1001 110
0011 010
0011 100
1001 100
1001 110
PIN-PACKAGE
16 QSOP
16 QSOP
16 QSOP
16 QSOP
16 TSSOP
16 TSSOP
16 TSSOP
16 TSSOP
MAX6699EE34
MAX6699EE38
MAX6699EE99
MAX6697EE9C
MAX6699UE34
MAX6699UE38
MAX6699UE99
MAX6697UE9C
Table 11. Slave Address
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6699UE | 5-Channel Precision Temperature Monitor |
| MAX6701-08_03 | Low-Voltage, SOT23 レP Supervisors with Power- Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701A-05A | Low-Voltage, SOT23 レP Supervisors with Power- Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701A-07A | Low-Voltage, SOT23 レP Supervisors with Power- Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701-08 | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6699EE34 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6699EE34+ | 功能描述:板上安裝溫度傳感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6699EE34+T | 功能描述:板上安裝溫度傳感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6699EE34-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6699EE38 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發(fā)布緊急采購，3分鐘左右您將得到回復。