- 您現在的位置：買賣IC網 > PDF目錄67881 > MAX6765TTYD0+ (MAXIM INTEGRATED PRODUCTS INC) Automotive Micropower Linear Regulators with Supervisor PDF資料下載
參數資料
| 型號： | MAX6765TTYD0+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Automotive Micropower Linear Regulators with Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO6 |
| 封裝： | 3 X 3 MM, 0.80 MM HIEGHT, LEAD FREE, MO-229WEEA, TDFN-6 |
| 文件頁數： | 8/46頁 |
| 文件大?。?/td> | 628K |
| 代理商： | MAX6765TTYD0+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
MAX6765–MAX6774
Automotive Micropower Linear Regulators
with Supervisor
16
______________________________________________________________________________________
Watchdog Timer (MAX6773/MAX6773B/
MAX6774/MAX6774B)
The MAX6773/MAX6774 include a watchdog timer that
asserts RESET if the watchdog input (WDI) does not
toggle within the watchdog timeout period tWD (1.6s
(typ) for the MAX6773/MAX6774 and 50ms (typ) for the
MAX6773B/MAX6774B). RESET remains low for the
reset timeout period, tRP. If the watchdog is not updat-
ed for lengthy periods of time, the reset output appears
as a pulse train, asserted for the reset timeout period
and deasserted for the watchdog timeout period, until
WDI is toggled again. When RESET asserts, it stays low
for the entire reset timeout period ignoring any WDI
transitions. To prevent the watchdog from asserting
RESET, toggle WDI with a valid rising or falling edge
prior to tWD (min). The watchdog counter clears when
WDI toggles prior to tWD or when RESET asserts. The
watchdog resumes counting after RESET deasserts.
The watchdog timer cannot be disabled.
Thermal Protection
When the junction temperature exceeds TJ = +160°C
(typ), an internal thermal sensor signals the shutdown
logic that turns off the pass transistor and allows the IC
to cool. The thermal sensor turns the pass transistor on
again after the IC’s junction temperature cools by 20°C
(typ), resulting in a cycled output during continuous
thermal-overload conditions. Thermal protection pro-
tects the MAX6765–MAX6774B in the event of a fault
condition. Never exceed the absolute maximum junction
temperature rating of TJ = +150°C. See Figures 3 and 4
for the safe operating area.
Applications Information
Output Voltage Selection
The MAX6767–MAX6774B feature dual-mode operation:
these devices operate in either a preset or adjustable
voltage mode. In preset voltage mode, internal trimmed
feedback resistors set the internal linear regulator to
+1.8V, +2.5V, +3.3V, or +5V (see Table 2). Select pre-
set-voltage mode by connecting SET to ground. In
adjustable mode, select an output voltage between
+1.8V and +11V using two external resistors connected
as a voltage-divider to SET (see Figure 1). Set the output
voltage using the following equation:
VOUT = VSET (1 + R1 / R2)
where VSET = 1.233V and the recommended value for
R2 is 50k (maximum 100k).
RESETIN Threshold Selection
The MAX6769/MAX6770 feature an adjustable reset
threshold to monitor the voltage on RESETIN using a
resistive divider between the monitored voltage,
RESETIN and GND. See Figure 2. Use the following for-
mula to set the desired reset threshold:
VMON = VTH (1 + R3 / R4)
where VTH is 1.085V for the M/S/Y/V versions and
1.147V for L/T/Z/W versions.
MAX6769
MAX6770
RESET
RESETIN
R3
R4
GND
IN
VIN
VMON
Figure 2. RESETIN Threshold Selection
OPERATING
STATE
ENABLE
HOLD
REGULATOR
OUTPUT
COMMENT
Initial State
Low
Don’t care
Off
ENABLE is pulled to GND through an internal pulldown. HOLD is
floating (pulled up to OUT). Regulator output is disabled.
Turn-On State
High
Don’t care
On
ENABLE is externally driven high turning the regulator output on.
HOLD is pulled up by OUT.
Hold
Setup State
High
Low
On
HOLD is externally pulled low while ENABLE remains high (latches
HOLD state).
Hold State
Low
On
ENABLE is driven low (or allowed to float low by an internal pulldown).
HOLD remains externally pulled low keeping the regulator output on.
Off-State
Low
High
(floats high)
Off
HOLD is driven high (or allowed to float high by an internal pullup)
while ENABLE is low. Regulator output is shut off and ENABLE/
HOLD logic returns to the initial state.
Table 3. ENABLE/HOLD Truth Table/State Table
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6765TTYD0+T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTYD1+ | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTYD1+T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTYD2+ | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTYD2+T | Automotive Micropower Linear Regulators with Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6765TTYD0+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/2.5V 0.1A 6TDFN EP - Rail/Tube |
| MAX6765TTYD0+T | 功能描述:線性穩壓器 - 標準 uPower Linear Regulator RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6765TTYD1+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/2.5V 0.1A 6TDFN EP - Rail/Tube |
| MAX6765TTYD1+T | 功能描述:線性穩壓器 - 標準 uPower Linear Regulator RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6765TTYD2+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/2.5V 0.1A 6TDFN EP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。