參數資料
型號： MAX7316AEE+
廠商： Maxim Integrated Products
文件頁數： 22/24頁
文件大?。?/td> 0K
描述： IC I/O EXPANDER I2C 16B 16QSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 100
接口： I²C，SM 總線
輸入/輸出數： 10
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 2 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 管件
Port Inputs and Transition Detection
The input ports register reflects the incoming logic lev-
els of the port pins, regardless of whether the pin is
defined as an input or an output. Reading the input
ports register latches the current-input logic level of the
affected eight ports. Transition detection allows all
ports configured as inputs to be monitored for changes
in their logic status. The action of reading the input
ports register samples the corresponding 8 port bits’
input condition. This sample is continuously compared
with the actual input conditions. A detected change in
input condition causes the INT/O8 interrupt output to go
low, if configured as an interrupt output. The interrupt is
cleared either automatically if the changed input
returns to its original state, or when the input ports reg-
ister is read.
The INT/O8 pin can be configured as either an interrupt
output or as a 9th output port with the same static or
blink controls as the other eight ports (Table 4).
Port Output Control and LED Blinking
The blink phase 0 register sets the output logic levels of
the eight ports P0–P7 (Table 8). This register controls
the port outputs if the blink function is disabled. A
duplicate register, the blink phase 1 register, is also
used if the blink function is enabled (Table 9). In blink
mode, the port outputs can be flipped between using
the blink phase 0 register and the blink phase 1 regis-
ter using hardware control (the BLINK input) and/or
software control (the blink flip flag in the configuration
register) (Table 4).
The logic level of the BLINK input can be read back
through the blink status bit in the configuration register
(Table 4). The BLINK input, therefore, can be used as a
general-purpose logic input (GPI port) if the blink func-
tion is not required.
PWM Intensity Control
The MAX7316 includes an internal oscillator, nominally
32kHz, to generate PWM timing for LED intensity control.
PWM intensity control can be enabled on an output-by-
output basis, allowing the MAX7316 to provide any mix
of PWM LED drives and glitch-free logic outputs (Table
10). PWM can be disabled entirely, in which case all out-
put ports are static and the MAX7316 operating current
is lowest because the internal oscillator is turned off.
PWM intensity control uses a 4-bit master control and 4
bits of individual control per output (Tables 13, 14). The
4-bit master control provides 16 levels of overall intensi-
ty control, which applies to all PWM-enabled output
ports. The master control sets the maximum pulse
width from 1/15 to 15/15 of the PWM time period. The
individual settings comprise a 4-bit number further
reducing the duty cycle to be from 1/16 to 15/16 of the
time window set by the master control.
For applications requiring the same PWM setting for all
output ports, a single global PWM control can be used
instead of all the individual controls to simplify the con-
trol software and provide 240 steps of intensity control
(Tables 10 and 13).
Standby Mode
When the serial interface is idle and the PWM intensity
control is unused, the MAX7316 automatically enters
standby mode. If the PWM intensity control is used, the
operating current is slightly higher because the internal
PWM oscillator is running. When the serial interface is
active, the operating current also increases because
the MAX7316, like all I2C slaves, has to monitor every
transmission.
MAX7316
10-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
_______________________________________________________________________________________
7
Figure 2. 2-Wire Serial Interface Timing Details
SCL
SDA
tR
tF
tBUF
START
CONDITION
STOP
CONDITION
REPEATED START CONDITION
START CONDITION
tSU,STO
tHD,STA
tSU,STA
tHD,DAT
tSU,DAT
tLOW
tHIGH
tHD,STA
相關PDF資料
PDF描述
ATMEGA8515L-8MUR MCU AVR 8KB FLASH 8MHZ 44QFN
MAX7316ATE+ IC I/O EXPANDER I2C 16B 16TQFN
ATMEGA8515-16MUR MCU AVR 8KB FLASH 16MHZ 44QFN
MAX7315ATE+T IC I/O EXPANDER I2C 8B 16TQFN-EP
MAX7315AUE+T IC I/O EXPANDER I2C 8B 16TSSOP
相關代理商/技術參數
參數描述
MAX7316AEE+ 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7316AEE+T 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7316AEE-T 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7316ATE 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7316ATE+ 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*