- 您現在的位置：買賣IC網 > PDF目錄3767 > MAX7316ATE+ (Maxim Integrated Products)IC I/O EXPANDER I2C 16B 16TQFN PDF資料下載
參數資料
| 型號： | MAX7316ATE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/24頁 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 16TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 10 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN-EP（3x3） |
| 包裝： | 管件 |
MAX7316
INT/O8 Output
The INT/O8 output pin can be configured as either the
INT output that reflects the interrupt flag logic state or as
a general-purpose output O8. When used as a general-
purpose output, INT/O8 has the same blink and PWM
intensity control capabilities as the other ports.
Set the interrupt enable I bit in the configuration register
to configure INT/O8 as the INT output (Table 4). Clear
interrupt enable to configure INT/O8 as the O8. The O8
logic state is set by the 2 bits O1 and O0 in the configu-
ration register. O8 follows the rules for blinking selected
by the blink enable flag E in the configuration register. If
blinking is disabled, then interrupt output control O0
alone sets the logic state of the INT/O8 pin. If blinking is
enabled, then both interrupt output controls O0 and O1
set the logic state of INT/O8 according to the blink
phase. PWM intensity control for O8 is set by the 4
global intensity bits in the master and O8 intensity reg-
ister (Table 13).
Blink Mode
In blink mode, the output ports can be flipped between
using either the blink phase 0 register or the blink
phase 1 register. Flip control is both hardware (the
BLINK input) and software control (the blink flip flag B
in the configuration register) (Table 4).
The blink function can be used for LED effects by pro-
gramming different display patterns in the two sets of
output port registers, and using the software or hard-
ware controls to flip between the patterns.
If the blink phase 1 register is written with 0xFF, then
the BLINK input can be used as a hardware disable to,
for example, instantly turn off an LED pattern pro-
grammed into the blink phase 0 register. This technique
can be further extended by driving the BLINK input with
a PWM signal to modulate the LED current to provide
fading effects.
The blink mode is enabled by setting the blink enable flag
E in the configuration register (Table 4). When blink mode
is enabled, the states of the blink flip flag and the BLINK
input are EXOR’ed to set the phase, and the output ports
are set by either the blink phase 0 register or the blink
phase 1 register (Figure 11) (Table 7).
10-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
12
______________________________________________________________________________________
Table 3. Power-Up Configuration
REGISTER DATA
REGISTER FUNCTION
POWER-UP CONDITION
ADDRESS
CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Blink phase 0 outputs P7–P0
High-impedance outputs
0x01
1
Ports configuration P7–P0
Ports P7–P0 are inputs
0x03
1
Blink phase 1 outputs P7–P0
High-impedance outputs
0x09
1
Master, O8 intensity
PWM oscillator is disabled;
O8 is static logic output
0x0E
0
1
Configuration
INT/O8 is interrupt output;
blink is disabled;
global intensity is enabled
0x0F
0
1
0
Outputs intensity P1, P0
P1, P0 are static logic outputs
0x10
1
Outputs Intensity P3, P2
P3, P2 are static logic outputs
0x11
1
Outputs intensity P5, P4
P5, P4 are static logic outputs
0x12
1
Outputs intensity P7, P6
P7, P6 are static logic outputs
0x13
1
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA8515-16MUR | MCU AVR 8KB FLASH 16MHZ 44QFN |
| MAX7315ATE+T | IC I/O EXPANDER I2C 8B 16TQFN-EP |
| MAX7315AUE+T | IC I/O EXPANDER I2C 8B 16TSSOP |
| AT90USB162-16MUR | IC AVR MCU 16K FLASH 32QFN |
| MAX7321ATE+T | IC I/O EXPANDER I2C 8B 16TQFN-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7316ATE+ | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316ATE+T | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316ATE-T | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7317 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Port SPI-Interfaced I/O Expander with Overvoltage and Hot-Insertion Protection |
| MAX7317AEE | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。