參數資料
型號: MAX7432EUD+T
廠商: Maxim Integrated Products
文件頁數: 3/21頁
文件大?。?/td> 0K
描述: IC FILTER VIDEO SD 14-TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
濾波器類型: 低通
頻率 - 截止或中心: 5MHz
濾波器數: 3
濾波器階數: 6th
電源電壓: 4.5 V ~ 5.5 V
安裝類型: 表面貼裝
封裝/外殼: 14-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 14-TSSOP
包裝: 帶卷 (TR)
MAX7428/MAX7430/MAX7432A
Standard Definition Video Reconstruction
Filters and Buffers
______________________________________________________________________________________
11
Applications Information
Maxim’s Single Pin Bus (MSPB)
Serial Interface
The MSPB interface uses three pulses of different
widths to represent commands and data bits. Figure 4
shows the set of pulses that the single pin interface
uses to communicate with the device. A combination of
the one pulse (t1), zero pulse (t0), transaction pulse (tT),
and prompt pulse (tP), writes to, reads back from, and
sends broadcast data to the devices on the bus.
Note: The zero pulse and prompt pulse are the same.
Initialization pulses are significantly longer and are
used only on power-up or software reset.
Initializing the
MAX7428/MAX7430/MAX7432A
Initialization is performed only after power-up or software
reset. It assigns a unique address to each device on the
bus. The time constant of the capacitor connected to
REXT in parallel with the 300k
Ω resistor determines the
order in which the devices are initialized (address
assigned). The device with the largest time constant is
initialized first and so on, in descending order. Table 7
shows the “Initialize Wait” and “Initialize Time” pulse
widths needed for a specific capacitor value and toler-
ance. Program each device on the bus with this com-
mand sequence starting with the device with the biggest
capacitor. To reinitialize a device, cycle the power or use
a software reset. The following is the command
sequence and timing diagram (Figure 5) for initialization
as shown below. Chip ID is entered LSB first.
Note: If there is only one device on the bus, no initial-
ization is needed. Communicate to the device using the
broadcast command described on page 13.
(MSB)
NAME
ABSEL3
BYPASS3
CLEVEL3
BOOST1(3)
BOOST0(3)
OUT
DISABLE3
DEFAULT
0
1
0
NAME
ABSEL2
BYPASS2
CLEVEL2
BOOST1(2)
BOOST0(2)
OUT
DISABLE2
DEFAULT
0
1
0
NAME
ABSEL1
BYPASS1
CLEVEL1
BOOST1(1)
BOOST0(1)
OUT
DISABLE1
DEFAULT
0
1
0
FIRST BIT
(LSB)
Table 5. MAX7432A Control Register
BOOST1_
BOOST0_
RELATIVE HIGH
FREQUENCY BOOST
00
0
1
0.3dB to 0.5dB
1
0
0.6dB to 1.0dB
1
0.9dB to 1.5dB
Table 6. Boost Level Programming
ZERO/PROMPT
PULSE
tP = t0 = 5
μs
t1 = 30
μs
t0
ONE PULSE
TRANSACTION
PULSE
t1
tT = 100
μs
tT
Figure 4. MSPB Interface Pulses
相關PDF資料
PDF描述
MAX7427EUA+T IC FILTER LOWPASS 5TH 8UMAX
MC9S08RD16DWE IC MCU 16K FLASH 1K RAM 28-SOIC
MAX7426EUA+T IC FILTER LOWPASS 5TH 8UMAX
MAX7426CPA+ IC FILTER LOWPASS 5TH 8-DIP
MAX7427CPA+ IC FILTER LOWPASS 5TH 8-DIP
相關代理商/技術參數
參數描述
MAX7432EVC16 功能描述:有源濾波器 Programmers, Development Systems RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube
MAX7432EVKIT 功能描述:有源濾波器 Programmers, Development Systems RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube
MAX7438ETP 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube
MAX7438ETP+ 功能描述:有源濾波器 Integrated Circuits (ICs) RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube
MAX7438ETP+T 功能描述:有源濾波器 Integrated Circuits (ICs) RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube