- 您現在的位置：買賣IC網 > PDF目錄383523 > MAX886ECJ (MAXIM INTEGRATED PRODUCTS INC) Analog IC PDF資料下載
參數資料
| 型號： | MAX886ECJ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Analog IC |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, TQFP-32 |
| 文件頁數： | 1/4頁 |
| 文件大小： | 57K |
| 代理商： | MAX886ECJ |
General Desc ription
The MAX881R IC is an inverting, charge-pump DC-DC
converter with a low-noise, regulated output. Low out-
put ripple voltage makes this device ideal for biasing
the GaAsFETs commonly found in cellular telephone
transmitters.
The MAX881R evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount board. Provisions are
made for mounting a second voltage-divider resistor,
which is required for setting output voltages other than
-2V. A special scope-probe socket is also mounted on
the board, so output noise can be observed on an
oscilloscope.
Features
o
1mVp-p Output Voltage Ripple
o
2.5V to 5.5V Input Range
o
Uses One 4.7μF and Three 1μF Ceramic
Capacitors
o
-2V Regulated Output (or Adjustable)
o
4mA Output Current
o
Power OK (
POK
) Output
o
Fully Assembled and Tested Surface-Mount
Board
Quic k S tart
The MAX881R EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Do not turn on the power supply until all connec-
tions are completed.
1) Connect a 2.5V to 5.5V supply to the pad labeled
VIN. Connect the ground lead to the pad labeled
GND.
2) Connect a voltmeter and the load to the VOUT pad.
3) Make sure there is no shunt across J U1.
4) Turn on the power and verify that the output is -2V.
You can insert a scope probe into J 1 to observe the
output noise. Be sure the scope ground makes con-
tact with the outside of the connector.
E
MAX 881R Evaluation K it
________________________________________________________________ Maxim Integrated Products
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
1
19-1372; Rev 1; 6/98
QTY
DESCRIPTION
C1, C2, C3
3
C4
1
J 1
1
Scope-probe connector
Berg Electronics 33J R135-1
2-pin jumper
J U1
R1
R2
R3, R4
U1
None
None
1
0
1
2
1
1
1
Not installed
100k
, 1% resistor
1M
resistors
MAX881RREUB
Shunt
Printed circuit board
4.7μF, 10V, low-ESR ceramic capacitor
Taiyo Yuden LMK316BJ 475ML
1μF, 16V, low-ESR ceramic capacitors
Taiyo Yuden EMK316BJ 105KL
SUPPLIER
PHONE
FAX
Berg Electronics
Sprague
Taiyo Yuden
(317) 738-2800
(603) 224-1961
(408) 573-4150
(317) 738-2858
(603) 224-1430
(408) 573-4159
DESIGNATION
Component List
PART
MAX881REVKIT
-40°C to +85°C
TEMP. RANGE
IC PACKAGE
10 μMAX
Ordering Information
Component S uppliers
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8875EUK15-T | Analog IC |
| MAX8877EUK15-T | Analog IC |
| MAX8877EUK18-T | Analog IC |
| MAX8877EUK25-T | VOLT REGULATOR|FIXED|+2.5V|CMOS|TSOP|6PIN|PLASTIC |
| MAX8877EUK28-T | VOLT REGULATOR|FIXED|+2.8V|CMOS|TSOP|6PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8873REUK | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX8873REUK+T | 功能描述:低壓差穩壓器 - LDO 120mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX8873REUK-T | 功能描述:低壓差穩壓器 - LDO 120mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX8873SEUK | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
| MAX8873SEUK+ | 制造商:Maxim Integrated Products 功能描述:LDO REG 1.25V TO 6.5V/2.84V 0.12A 5PIN SOT-23 - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。