- 您現在的位置：買賣IC網 > PDF目錄10650 > MAX907CSA+T (Maxim Integrated Products)IC COMPAR HS DUAL 8-SOIC PDF資料下載
參數資料
| 型號： | MAX907CSA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMPAR HS DUAL 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 通用 |
| 元件數： | 2 |
| 輸出類型： | TTL |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 11 V |
| 電壓 - 輸入偏移（最小值）： | 2mV @ 5V |
| 電流 - 輸入偏壓（最小值）： | 0.3µA @ 5V |
| 電流 - 靜態（最大值）： | 1mA |
| CMRR, PSRR（標準）： | 86.02dB CMRR，86.02dB PSRR |
| 傳輸延遲（最大）： | 50ns |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 安裝類型： | 表面貼裝 |
| 包裝： | 帶卷 (TR) |
MAX907/MAX908/MAX909
Dual/Quad/Single, High-Speed, Ultra-Low-Power,
Single-Supply TTL Comparators
4
_______________________________________________________________________________________
Note 1:
Trip Point is defined as the input voltage required to make the comparator output change state. The difference
between upper (VTRIP+) and lower (VTRIP-) trip points is equal to the width of the input-referred hysteresis zone (VHYST).
Specified for an input common-mode voltage (VCM) of 0V (see Figure 1).
Note 2:
Input Offset Voltage is defined as the center of the input-referred hysteresis zone. Specified for VCM = 0V (see Figure 1).
Note 3:
Inferred from the CMRR test. Note that a correct logic result is obtained at the output, provided that at least one input is
within the VCMR limits. Note also that either or both inputs can be driven to the upper or lower absolute maximum limit with-
out damage to the part.
Note 4:
Tested with V+ = 5.5V (and V- = 0V for MAX909). MAX909 also tested over the full analog input range (i.e., with
V- = -5.5V).
Note 5:
Tested over the full input voltage range (VCMR).
Note 6:
Specified over the full tolerance of operating supply voltage: MAX907/MAX908 tested with 4.5V < V+ < 5.5V. MAX909
tested with 4.5V < V+ < 5.5V and with -5.5V < V- < 0V.
Note 7:
Positive Supply Current specified with the worst-case condition of all outputs at logic low (MAX907/MAX908), and
with V+ = 5.5V.
Note 8:
Typical power specified with V+ = 5V; maximum with V+ = 5.5V (and with V- = -5.5V for MAX909).
Note 9:
Due to difficulties in measuring propagation delay with 5mV of overdrive in automatic test equipment, this parameter is
guaranteed by design for the MAX907 and MAX908. Correlation tests show that the specification can be guaranteed if all
other DC parameters are within the specified limits. VOS must be added to the overdrive voltage for low values of overdrive.
For the MAX909, propagation delay is typical only and there is no guaranteed maximum limit.
Note 10: Differential Propagation Delay is specified as the difference between any two channels in the MAX907/MAX908 (both out-
puts making either a low-to-high or a high-to-low transition).
Note 11: Propagation Delay Skew is specified as the difference between any single channel’s output low-to-high transition (tPD+)
and high-to-low transition (tPD-), and also between the QOUT and QOUT transition on the MAX909.
Note 12: Latch specifications apply to MAX909 only (see Figure 2).
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 5V, TA = TMIN to TMAX; MAX909 only: V- = 0V, VLATCH = 0V; unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Propagation Delay
tPD+, tPD-
VIN = 100mV, VOD = 5mV
(Note 9)
45
70
ns
Differential Propagation Delay
tPD
VIN = 100mV, VOD = 5mV
(Note 10)
2
ns
Propagation Delay Skew
tPDskew
MAX909 only: VIN = 100mV,
VOD = 5mV (Note 11)
4
ns
Latch Input Voltage High
VIH
(Note 12)
2.0
V
Latch Hold Time
th
(Note 12)
4
ns
Latch Input Voltage Low
VIL
(Note 12)
0.8
V
Latch Input Current
IIH, IIL
(Note 12)
20
A
Latch Setup Time
ts
(Note 12)
4
ns
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J52-MY-F2 | CONVERTER MOD DC/DC 15V 50W |
| MAX971CUA+T | IC COMPARATOR OD 8-UMAX |
| VE-BWX-MX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MAX971ESA+T | IC COMPARATOR OD 8-SOIC |
| MAX3221CAE+ | IC TXRX RS232 120KBPS SD 16-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX907EP | 制造商:Maxim Integrated Products 功能描述: |
| MAX907EPA | 功能描述:校驗器 IC Dual TTL Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX907EPA+ | 功能描述:校驗器 IC Dual TTL Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX907ESA | 功能描述:校驗器 IC Dual TTL Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX907ESA+ | 功能描述:校驗器 IC Dual TTL Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。