- 您現在的位置：買賣IC網 > PDF目錄10618 > MAX9135GHJ+ (Maxim Integrated Products)IC SW LVDS CROSSBAR 32TQFP-EP PDF資料下載
參數資料
| 型號： | MAX9135GHJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SW LVDS CROSSBAR 32TQFP-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 360 |
| 類型： | LVDS 縱橫開關 |
| 應用： | 數字視頻 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP 裸露焊盤 |
| 供應商設備封裝： | 32-TQFP-EP（5x5） |
| 包裝： | 管件 |
MAX9132/MAX9134/MAX9135
Programmable, High-Speed, Multiple
Input/Output LVDS Crossbar Switches
______________________________________________________________________________________
13
face. The routing action takes place after correct check-
sum verification. The LIN status register (0x00) holds the
error flags for the LIN transceiver. For a write, the master
writes 2 bytes of data to the registers (0x01, 0x02). For a
read, the slave outputs the contents of registers 0x00,
0x01, and 0x02, along with the stuffing byte at a constant
value (0xFF). In either mode, the checksum follows at the
end of the data bytes. Figure 3 shows the write and read
signal frame format. Figure 4 shows the LIN write and
read data frame.
LIN-Protected Identifier
The LIN bus uses the 8-bit protected identifier (PID) to
address the slave nodes. Two parity bits (MSBs) along
with 6 ID bits (LSBs) make up the PID field. Table 4
defines the sets of the identifiers for the write/read
operations of the LIN slave node. AS0 selects the iden-
tifiers. AS1/NSLP becomes the NSLP output for activat-
ing the LIN driver chip (MAX13020).
LIN Error Handling
Register 0x00 contains the error flags found in the LIN
signal by the slave note (Table 5). A successful LIN
read resets register 0x00.
Pin Control by S[5:0] (MAX9134/MAX9135)
For the MAX9134/MAX9135, the routing can be con-
trolled by the hardware pins (S[5:0]). If the I2C register
0xFF is not written by 0xFF, then chip routing is deter-
mined by S[5:0]. Also, these pins set the initial power-
up routing condition of the chip. Table 6a gives the
details of the routing control for the MAX9134. Table 6b
gives the details of the routing control for the MAX9135.
Once the I2C register 0xFF is written by 0xFF, the I2C
registers 0x01 and 0x02 take over the routing and the
pin (S[5:0]) setting is ignored. After the I2C routing
takes place, the pin setting can be changed without
affecting the routing. The new pin setting takes effect if
the PD pin or the chip supply is toggled. Usually, once
I2C controls the routing, there is no value in using the
pin routing.
Applications Information
3-Level Inputs
The MAX9132/MAX9134/MAX9135 use several 3-level
inputs to control the device. Use three-state logic to
realize the 3-level logic using digital control.
Alternatively, if a high-impedance output is unavailable,
apply a voltage of VDD/2 to realize the midlevel high-
impedance state.
WRITE ID
READ ID
AS0
ID[5:0]
PID FIELD
ID[5:0]
PID FIELD
Low
0x08
0x27
0xE7
Open
0x0A
0xCA
0x29
0xE9
High
0x1C
0x9C
0x2B
Table 4. LIN Identifiers for Write and Read Operations
REGISTER BIT(S)
DESCRIPTION
FUNCTION
D[7:5]
Reserved
D4
Sync
Sync pulse widths outside the given tolerances detected
D3
Transmit
Value read on RXD different from value transmitted on TXD during a read
D2
Checksum
Checksum sent during a write does not match the expected checksum
D1
Parity
ID parity bit does not match expected parity
D0
Frame
Message frame did not complete within the maximum allowed time
Table 5. Register 0x00 Error Flag Mapping for LIN
MAX9132
MAX9134
MAX9135
VBAT
MAX13020
VDD
INH
TXD
RXD
NSLP
LIN
BUS
TXD
5kΩ
RXD
NSLP
NWAKE
LIN
Figure 5. Connecting the MAX9132/MAX9134/MAX9135 to the
MAX13020
相關PDF資料 |
PDF描述 |
|---|---|
| MAX242EWN+ | IC TXRX RS232 5V 18-SOIC |
| MAX9134GHJ+ | IC SW LVDS CROSSBAR 32TQFP-EP |
| MAX232AEWE+ | IC 2DVR/2RCVR RS232 5V 16-SOIC |
| MAX3815ACCM+ | IC DGTL VIDEO EQUALIZER 48TQFP |
| MAX3816ACUE+ | IC I2C 2WIRE EXTENDER 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9135GHJ+ | 功能描述:LVDS 接口集成電路 Programmable LVDS Crossbar Switch RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX9135GHJ+T | 功能描述:LVDS 接口集成電路 Programmable LVDS Crossbar Switch RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX913C | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| MAX913C/D | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX913CPA | 功能描述:校驗器 IC Single Precision TTL Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。