- 您現在的位置：買賣IC網 > PDF目錄383539 > MAX913 (Maxim Integrated Products, Inc.) Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators PDF資料下載
參數資料
| 型號： | MAX913 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| 中文描述： | 單/雙路、超高速、低功耗、高精度TTL比較器 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 93K |
| 代理商： | MAX913 |
_______________Detailed Desc ription
The MAX913 (single) and MAX912 (dual) high-speed
comparators have a unique design that prevents oscil-
lation when the comparator is in its linear region. No
minimum input slew rate is required.
Many high-speed comparators oscillate in the linear
region, as shown in the Typical Operating
Characteristics’ industry-standard 686 response graph.
One way to overcome this oscillation is to sample the
output after it has passed through the unstable region.
Another practical solution is to add hysteresis. Either
solution results in a loss of resolution and bandwidth.
Because the MAX912/MAX913 do not need hysteresis,
they offer high resolution to all signals—including low-
frequency signals.
The MAX912/MAX913 provide a TTL-compatible latch
function that holds the comparator output state (Figure 1).
As long as Latch Enable (LE) is high or floating, the input
signal has no effect on the output state. With LE low, the
outputs are controlled by the input differential voltage and
the latch is transparent.
Input Amplifier
A comparator can be thought of as having two sec-
tions: an input amplifier and a logic interface. The
MAX912/MAX913’s input amplifier is fully differential,
with input offset voltage trimmed to below 2.0mV at
+25°C. Input common-mode range extends from
200mV
below
the negative supply rail to 1.5V below the
positive power supply. The total common-mode range
is 8.7V when operating from ±5VDC supplies.
The MAX912/MAX913’s amplifier has no built-in hys-
teresis. For highest accuracy, do not add hysteresis.
Figure 2 shows how hysteresis degrades resolution.
Resolution
A comparator’s ability to resolve small signal differ-
ences—its resolution—is affected by various factors.
As with most amplifiers, the most significant factors are
the input offset voltage (V
OS
) and the common-mode
and power-supply rejection ratios (CMRR, PSRR). If
source impedance is high, input offset current can be
significant. If source impedance is unbalanced, the
input bias current can introduce another error.
For high-speed comparators, an additional factor in reso-
lution is the comparator’s stability in its linear region. Many
high-speed comparators are useless in their linear region
because they oscillate. This makes the differential input
voltage region around 0V unusable, as does a high V
OS.
Hysteresis does not cure the problem, but acts to keep
the input away from its linear range (Figure 2).
The MAX912/MAX913 do not oscillate in the linear region,
which greatly enhances the comparator’s resolution.
__________Applic ations Information
Power S upplies and Bypassing
The MAX912/MAX913 are tested with ±5V power sup-
plies that provide an input common-mode range (V
CM
)
of 8.7V (-5.2V to +3.5V). Operation from a single +5V
supply provides a common-mode input range of 3.7V
(-0.2V to +3.5V). Connect V- to GND for single-supply
operation. The MAX912/MAX913 will operate from a
minimum single-supply voltage of +4.5V.
The V+ supply provides power to both the analog input
stage and digital output circuits, whereas the V- supply
only powers the analog section. Bypass V+ and V- to
ground with 0.1μF to 1.0μF ceramic capacitors in parallel
with 10μF or greater tantalum capacitors. Connect the
ceramic capacitors very close to the MAX912/MAX913’s
M
S ingle/Dual, Ultra-Fast, Low-Power,
Prec ision T T L Comparators
_______________________________________________________________________________________
7
t
SU
t
H
t
PD+
t
PD
t
PD-
t
LPDR
Q
Q
V
IN
(DIFFERENTIAL)
LATCH
ENABLE (LE)
Figure 1. Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX913C | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| MAX913D | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| MAX912CPE | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| MAX912C | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
| MAX912EPE | Single/Dual, Ultra-Fast, Low-Power, Precision TTL Comparators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9130 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single 500Mbps LVDS Line Receiver in SC70 |
| MAX9130EXT | 制造商:Maxim Integrated Products 功能描述:SINGLE 500MBPS LVDS LINE RECEIVER I - Cut Tape Product |
| MAX9130EXT+ | 制造商:Maxim Integrated Products 功能描述:LINE RCVR 1RX 6PIN SC-70 - Rail/Tube |
| MAX9130EXT+T | 功能描述:LVDS 接口集成電路 Single 500Mbps LVDS Line Receiver RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX9130EXT-T | 功能描述:LVDS 接口集成電路 RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。