- 您現在的位置：買賣IC網 > PDF目錄11129 > MAX9152EUE+T (Maxim Integrated Products)IC CROSSPOINT SWITCH 2X2 16TSSOP PDF資料下載
參數資料
| 型號： | MAX9152EUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CROSSPOINT SWITCH 2X2 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 交叉點開關 |
| 電路： | 1 x 2:2 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
Input Fail-Safe
The differential inputs of the MAX9152 do not have
internal fail-safe biasing. If fail-safe biasing is required,
it can be implemented with external large-value resis-
tors. IN_+ should be pulled up to VCC with 10k
and
IN_ should be pulled down to GND with 10k
. The volt-
age-divider formed by the 10k
resistors and the 100
termination resistor (across IN_+ and IN_-) provides a
slight positive differential bias and sets a high state at
the device output when inputs are undriven.
Output Resistance
The MAX9152 has a selectable differential output resis-
tance to reduce reflections from impedance discontinu-
ities in the interconnect. Reflections are reduced,
compared to a high-impedance output. A termination
resistor at the receiver is still required and is the primary
termination for the interconnect. Select the output resis-
tance that best matches the differential characteristic
impedance of the interconnect used.
Select Function
The SEL0 and SEL1 logic inputs allow the device to be
configured as a high-speed differential crosspoint, 2:1
mux, 1:2 demux, dual repeater, or 1:2 splitter (Figure
8). See Table 1 for mode selection settings.
Enable Function
The EN0 and EN1 logic inputs enable and disable dri-
ver outputs OUT0 and OUT1. Setting EN0 or EN1 high
enables the corresponding driver output. Setting EN0
MAX9152
800Mbps LVDS/LVPECL-to-LVDS 2 x 2
Crosspoint Switch
_______________________________________________________________________________________
7
1.5V
EN0 = EN1 = HIGH
VID = (VIN_+)
(VIN_-)
tHOLD
tSWITCH
tSET
VID = 0
IN1
IN0
IN0+
IN0-
IN1-
IN1+
OUT_-
SEL_
OUT_+
1.5V
EN0 = EN1 = HIGH
VID = (VIN_+)
(VIN_-)
tHOLD
tSWITCH
tSET
VID = 0
IN0
IN1
IN0+
IN0-
IN1-
IN1+
OUT_+
SEL_
OUT_-
Figure 2. Input to Rising Edge Select Setup, Hold, and Mux Switch Timing Diagram
Figure 3. Input to Falling Edge Select Setup, Hold, and Mux Switch Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4053CSE+ | IC MULTIPLEXER TRPL 2X1 16SOIC |
| UPD78F1152AGK-GAK-AX | MCU 16BIT 78K0R/KX3 80-LQFP |
| MAX4545EAP+T | IC VIDEO SWITCH QUAD SPST 20SSOP |
| UPD78F1143AGK-GAJ-AX | MCU 16BIT 78K0R/KX3 64-LQFP |
| MAX4712CUE+T | IC SWITCH QUAD SPST 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9153 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Jitter, 800Mbps, 10-Port LVDS Repeaters with 100 зDrive |
| MAX9153EUI | 制造商:Maxim Integrated Products 功能描述:LOW-JITTER, 800MBPS, 10-PORT LVDS REPEATERS W - Bulk |
| MAX9153EUI+ | 功能描述:LVDS 接口集成電路 800Mbps 10-Port LVDS Repeater RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX9153EUI+T | 功能描述:LVDS 接口集成電路 800Mbps 10-Port LVDS Repeater RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX9153EUI-T | 制造商:Maxim Integrated Products 功能描述:LOW-JITTER, 800MBPS, 10-PORT LVDS REPEATERS W - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。