When VCC
參數資料
型號: MAX9207EAI+
廠商: Maxim Integrated Products
文件頁數: 10/13頁
文件大?。?/td> 0K
描述: IC SERIALIZER LVDS 28-SSOP
其它有關文件: Automotive Product Guide
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 46
功能: 串行器
數據速率: 660Mbps
輸入類型: LVTTL/LVCMOS
輸出類型: LVDS
輸入數: 10
輸出數: 1
電源電壓: 3 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 28-SSOP
包裝: 管件
MAX9205/MAX9207
10-Bit Bus LVDS Serializers
6
Maxim Integrated
Initialization Mode
When VCC is applied, the outputs are held in high
impedance and internal circuitry is disabled by on-chip
power-on-reset circuitry. When the supply voltage
reaches 2.35V, the PLL starts to lock to a local refer-
ence clock (16MHz to 40MHz for MAX9205 and 40MHz
to 66MHz for MAX9207). The reference clock, TCLK, is
provided by the system. A serializer locks within 2049
cycles of TCLK. Once locked, a serializer is ready to
send data or SYNC patterns depending on the levels of
SYNC 1 and SYNC 2.
Synchronization Mode
To rapidly synchronize with a deserializer, SYNC pat-
terns can be sent. A SYNC pattern is six consecutive
ones followed by six consecutive zeros repeating every
TCLK period. When one or both SYNC inputs are
asserted high for at least six cycles of TCLK, the serial-
izer will initiate the transmission of 1024 SYNC patterns.
The serializer will continue to send SYNC patterns if
either of the SYNC input pins remains high. Toggling
one SYNC input with the other SYNC input low before
1024 SYNC patterns are output does not interrupt the
output of the 1024 SYNC patterns.
Data Transmission Mode
After initialization, both SYNC input pins must be set
low by users or through a control signal from the dese-
rializer before data transmission begins. Provided that
SYNC inputs are low, input data at IN0–9 are clocked
into the serializer by the TCLK input. Setting TCLK_R/F
high selects the rising edge of TCLK for data strobe
and low selects the falling edge. If either of the SYNC
inputs goes high for six TCLK cycles at any time during
data transmission, the data at IN0–9 are ignored and
SYNC patterns are sent for at least 1024 TCLK cycles.
A start bit high and a stop bit low frame the 10-bit data
and function as the embedded clock edge in the serial
data stream. The serial rate is the TCLK frequency
times the data and appended bits. For example, if
TCLK is 40MHz, the serial rate is 40 x 12 (10 + 2 bits) =
480Mbps. Since only 10 bits are from input data, the
payload rate is 40 x 10 = 400Mbps.
Power-Down
Power-down mode is entered when the PWRDN pin is
driven low. In power-down mode, the PLL of the serial-
izer is stopped and the outputs (OUT+ and OUT-) are
in high impedance, disabling drive current and also
reducing supply current. When PWRDN is driven high,
the serializer must reinitialize and resynchronize before
data can be transferred. On power-up, in order for the
MAX9205/MAX9207 to initialize correctly, PWRDN should
remain below 0.7V until PCLK is stable and all power sup-
plies are within specification.
High-Impedance State
The serializer output pins (OUT+ and OUT-) are held in
high impedance when the supply voltage is first
applied and while the PLL is locking to the local refer-
ence clock. Setting EN or PWRDN low puts the device
in high impedance. After initialization, EN functions
asynchronously. For example, the serializer output can
be put into high impedance while SYNC patterns are
being sent without affecting the internal timing of the
SYNC pattern generation. However, if the serializer
goes into high impedance, a deserializer loses PLL
lock and needs to resynchronize before data transfer
can resume.
Table 1. Input /Output Function Table
INPUTS
OUTPUTS
EN
PWRDN
SYNC 1
SYNC 2
OUT+, OUT-
HH
When either or both SYNC 1
and SYNC 2 are held high for
at least six TCLK cycles
Synchronization Mode. SYNC patterns of six 1s and six 0s are
transmitted every TCLK cycle for at least 1024 TCLK cycles.
Data at IN0–9 are ignored.
HH
L
Data Transmission Mode. IN0–9 and 2 frame bits are
transmitted every TCLK cycle.
XL
X
LX
X
Output in high-impedance.
X = Don’t care.
相關PDF資料
PDF描述
V72B8H150BF3 CONVERTER MOD DC/DC 8V 150W
V72B5H150BL CONVERTER MOD DC/DC 5V 150W
D38999/26JE26PA CONN PLUG 26POS STRAIGHT W/PINS
V72B5H150BG CONVERTER MOD DC/DC 5V 150W
MS3100E32-15S CONN RCPT 8POS WALL MNT W/SCKT
相關代理商/技術參數
參數描述
MAX9207EAI+ 功能描述:串行器/解串器 - Serdes 10-Bit Bus LVDS Serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64
MAX9207EAI+T 功能描述:串行器/解串器 - Serdes 10-Bit Bus LVDS Serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64
MAX9207EAI-T 功能描述:LVDS 接口集成電路 RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel
MAX9208 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit Bus LVDS Deserializers
MAX9208EAI 功能描述:LVDS 接口集成電路 RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel