- 您現在的位置：買賣IC網 > PDF目錄383541 > MAX922CPA (MAXIM INTEGRATED PRODUCTS INC) Ultra Low-Power, Single/Dual-Supply Comparators PDF資料下載
參數資料
| 型號： | MAX922CPA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Ultra Low-Power, Single/Dual-Supply Comparators |
| 中文描述： | DUAL COMPARATOR, 10000 uV OFFSET-MAX, 14000 ns RESPONSE TIME, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 139K |
| 代理商： | MAX922CPA |
M
comparator is used with the reference, the combined
peak-to-peak noise is about 1mV. This, of course, is
much higher than the RMS noise of the individual
components. Care should be taken in the layout to
avoid capacitive coupling from any output to the
reference pin. Crosstalk can significantly increase the
actual noise of the reference.
__________Applic ations Information
Hysteresis
Hysteresis increases the comparators’ noise margin by
increasing the upper threshold and decreasing the
lower threshold (see Figure 2).
Hysteresis (MAX921/MAX923)
To add hysteresis to the MAX921 or MAX923, connect
resistor R1 between REF and HYST, and connect
resistor R2 between HYST and V- (Figure 3). If no
hysteresis is required, connect HYST to REF. When
hysteresis is added, the upper threshold increases by
the same amount that the lower threshold decreases.
The hysteresis band (the difference between the upper
and lower thresholds, V
HB
) is approximately equal to
twice the voltage between REF and HYST. The HYST
input can be adjusted to a maximum voltage of REF
and to a minimum voltage of (REF – 50mV). The
maximum difference between REF and HYST (50mV)
will therefore produce a 100mV max hysteresis band.
Use the following equations to determine R1 and R2:
V
2
I
REF
×
Where I
REF
(the current sourced by the reference)
should not exceed the REF source capability, and
should be significantly larger than the HYST input
current. I
REF
values between 0.1μA and 4μA are
usually appropriate. If 2.4M
is chosen for R2 (I
REF
=
0.5μA), the equation for R1 and V
HB
can be
approximated as:
R1 (k ) = V
(mV)
HB
When hysteresis is obtained in this manner for the
MAX923, the same hysteresis applies to both comparators.
Hysteresis (MAX922/MAX924)
Hysteresis can be set with two resistors using positive
feedback, as shown in Figure 4. This circuit generally
draws more current than the circuits using the HYST
pin on the MAX921 and MAX923, and the high
feedback impedance slows hysteresis. The design
procedure is as follows:
1. Choose R3. The leakage current of IN+ is under
1nA (up to +85°C), so the current through R3 can be
around 100nA and still maintain good accuracy.
The current through R3 at the trip point is V
REF
/R3,
or 100nA for R3 = 11.8M
. 10M
is a good
practical value.
2. Choose the hysteresis voltage (V
HB
), the voltage
between the upper and lower thresholds. In this
example, choose V
HB
= 50mV.
3. Calculate R1.
V
V
0.05
5
100k
=
4. Choose the threshold voltage for V
IN
rising (V
THR
).
In this example, choose V
THR
= 3V.
5. Calculate R2.
1
A 1% preferred value is 64.9k
.
R2 =
V
(V
1
R1
1
R3
3
×
(1.182
100k)
1
100k
1
10M
65.44k
THR
×
REF
R1)
1
=
=
R1 = R3
10M
HB
+
×
=
×
R1 =
R2 =
1.182 ± V
2
I
HB
HB
REF
(
)
Ultra Low-Power,
S ingle/Dual-S upply Comparators
10
______________________________________________________________________________________
GND
V-
V+
MAX924
OUT
R3
R1
R2
V
REF
V
IN
V+
Figure 4. External Hysteresis
相關PDF資料 |
PDF描述 |
|---|---|
| MAX922CSA | Ultra Low-Power, Single/Dual-Supply Comparators |
| MAX922EPA | Ultra Low-Power, Single/Dual-Supply Comparators |
| MAX922ESA | Ultra Low-Power, Single/Dual-Supply Comparators |
| MAX922MJA | Ultra Low-Power, Single/Dual-Supply Comparators |
| MAX924CSE | Ultra Low-Power, Single/Dual-Supply Comparators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX922CPA+ | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX922CSA | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX922CSA+ | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX922CSA+T | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX922CSA-T | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。