- 您現在的位置：買賣IC網 > PDF目錄2090 > MAX9513ATE+T (Maxim Integrated Products)IC AMP VIDEO FILTER 16-TQFN PDF資料下載
參數資料
| 型號： | MAX9513ATE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/23頁 |
| 文件大小： | 0K |
| 描述： | IC AMP VIDEO FILTER 16-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 應用： | 濾波器 |
| 電路數： | 1 |
| 電流 - 電源： | 13mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
MAX9513
CVBS Video Filter Amplifier with SmartSleep
and Bidirectional Video Support
18
______________________________________________________________________________________
Inputs
The MAX9513 CVBSIN input should be directly con-
nected to the output of the video current DAC. DC-cou-
pling ensures that the input signals are ground
referenced such that the sync tip of CVBSIN is within
50mV of ground.
The EXTCVBSIN input can only handle signals with a
sync pulse, such as composite video and luma.
Because the DC level of an external video input signal
is unknown, the external video signal is AC-coupled
through a 0.1F capacitor, and a sync tip clamp sets
the internal DC level of the MAX9513. A 2:1 multiplexer
under the control of the INT/EXT input selects either the
signal at CVBSIN or EXTCVBSIN.
Video Reconstruction Filter
The MAX9513 filter passband is 6.75MHz, which makes
the device suitable for the higher bandwidth video sig-
nals from a DVD chip. Broadcast video signals actually
require less bandwidth because of channel limitations:
NTSC signals have a 4.2MHz bandwidth, and PAL sig-
nals have a 5MHz bandwidth. Video signals from a DVD
player are not channel limited; therefore, the bandwidth
of DVD video signals can push right against the Nyquist
limit of 6.75MHz. (Recommendation ITU-R BT.601-5
specifies 13.5MHz as the sampling rate for standard-
definition video). Therefore, the maximum bandwidth of
the signal is 6.75MHz. To reduce the filtering require-
ments, most modern video systems oversample the
input by two times, thus clocking the video current DAC
at 27MHz.
Outputs
The video output amplifiers can both source and sink
load current, allowing output loads to be DC- or AC-
coupled. The amplifier output stage needs approxi-
mately 300mV of headroom from either supply rail. The
MAX9513 has an internal level-shift circuit that positions
the sync tip at approximately 300mV at the output.
If the supply voltage is greater than 3.135V (5% below
a 3.3V supply), each amplifier can drive two DC-cou-
pled video loads to ground. If the supply is less than
3.135V, each amplifier can drive only one DC-coupled
or AC-coupled video load.
Shutdown
When SHDN is low, the MAX9513 typically draws less
than 10nA supply current. All the amplifier outputs
become high impedance. The effective output resis-
tance at the video outputs is 28k
Ω, due to the internal
feedback resistors to ground.
Applications Information
Reducing Power Consumption
in the Video DACs
CVBSIN has a high-impedance input buffer and can
work with source resistances as high as 300
Ω. To
reduce power dissipation in the video DACs, the DAC
output resistor can be scaled up in value. The reference
resistor that sets the reference current inside the video
DACs must also be similarly scaled up. For instance, if
the output resistor is 37.5
Ω, the DAC must source
26.7mA when the output is 1V. If the output resistor is
increased to 300
Ω, the DAC only needs to source
3.33mA when the output is 1V.
There is parasitic capacitance from the DAC output to
ground. That capacitance in parallel with the DAC out-
put resistor forms a pole that can potentially roll off the
frequency response of the video signal. For example,
300
Ω in parallel with 50pF creates a pole at 10.6MHz.
To minimize this capacitance, reduce the area of the
signal trace attached to the DAC output as much as
possible, and place the MAX9513 as close to the video
DAC outputs as possible.
AC-Coupling the Outputs
The outputs can be AC-coupled since the output stage
can source and sink current as shown in Figure 9.
Coupling capacitors should be 220F or greater to keep
the highpass filter formed by the 150
Ω equivalent resis-
tance of the video transmission line to a corner frequen-
cy of 4.8Hz or below. The frame rate of PAL systems is
25Hz, and the frame rate of NTSC systems is 30Hz. The
corner frequency should be well below the frame rate.
SmartSleep only works with DC-coupled loads.
Power-Supply Bypassing and Ground
The MAX9513 operates from a single-supply voltage
down to 2.7V, allowing for low-power operation. Bypass
VDD to GND with a 0.1F capacitor. Place all external
components as close as possible to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9515ABS+T | IC VIDEO FILTER AMP W/SD 4-UCSP |
| MAX9516ALB+T | IC VIDEO FILTER AMP 1.8V 10-UDFN |
| MAX9519ARS+T | IC AMP VIDEO FILTER 4-UCSP |
| MAX951EUA+ | IC OP AMP SS LP 8-UMAX |
| MAX9524ATC+T | IC STD-DEF VID FILT AMP12TQFN-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9513EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX9513 EVAL KIT - Rail/Tube |
| MAX9515ABS+T | 功能描述:視頻放大器 Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX9515ABS+TG45 | 制造商:Maxim from Components Direct 功能描述:MAXIM MAX9515ABS+TG45 VIDEO AMPLIFIERS - Tape and Reel 制造商:Maxim 功能描述:Maxim MAX9515ABS+TG45 Video Amplifiers |
| MAX9515EVKIT+ | 功能描述:放大器 IC 開發工具 MAX9515 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9516ALB+ | 制造商:Maxim Integrated Products 功能描述:1.8V, ULTRA-LOW-POWER, DIRECTDRIVE VIDEO FILTER AMPLIFIER - Bulk |
發布緊急采購，3分鐘左右您將得到回復。