- 您現在的位置：買賣IC網 > PDF目錄2090 > MAX9597CTI+ (Maxim Integrated Products)IC AUD/VID INTERACE 28TQFN-EP PDF資料下載
參數資料
| 型號： | MAX9597CTI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AUD/VID INTERACE 28TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 類型： | 音頻/視頻接口 |
| 應用： | DVD，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
MAX9597
Low-Power Audio/Video Interface
for Single SCART Connectors
16
______________________________________________________________________________________
Fast Switching
The fast-switching signal was originally used to switch
between CVBS and RGB signals on a pixel-by-pixel
basis so that on-screen display (OSD) information
could be inserted. Since modern set-top box decoder
chips have integrated OSD circuitry, there is no need to
create OSD information using the older technique.
Now, the fast-switching signal is just used to switch
between CVBS and RGB signal sources.
Set the source of the fast-switching signal by writing to
bits 4 and 3 of register 07h. The fast-switching signal to
the TV SCART connector can be enabled or disabled
by bit 1 of register 0Dh. See Tables 9 and 11.
I2C Serial Interface
The MAX9597 features an I2C/SMBus-compatible,
2-wire serial interface consisting of a serial-data line
(SDA) and a serial-clock line (SCL). SDA and SCL facili-
tate communication between the MAX9597 and the mas-
ter at clock rates up to 400kHz. Figure 4 shows the
2-wire interface timing diagram. The master generates
SCL and initiates data transfer on the bus. A master
device writes data to the MAX9597 by transmitting a
START (S) condition, the proper slave address with the
R/W bit set to 0, followed by the register address and
then the data word. Each transmit sequence is framed
by a START and a STOP (P) condition. Each word trans-
mitted to the MAX9597 is 8 bits long and is followed by
an acknowledge clock pulse. A master reads from the
MAX9597 by transmitting the slave address with the R/W
bit set to 0, the register address of the register to be
read, a REPEATED START (Sr) condition, the slave
address with the R/W bit set to 1, followed by a series of
SCL pulses. The MAX9597 transmits data on SDA in
sync with the master-generated SCL pulses. The master
acknowledges receipt of each byte of data. Each read
sequence is framed by a START or REPEATED START
condition, an acknowledge or a not acknowledge, and a
STOP condition. SDA operates as both an input and an
open-drain output. A pullup resistor, typically greater
than 500, is required on the SDA bus. SCL operates as
only an input. A pullup resistor, typically greater than
500, is required on SCL if there are multiple masters on
the bus, or if the master in a single-master system has an
open-drain SCL output. Series resistors in line with SDA
and SCL are optional. Series resistors protect the digital
inputs of the MAX9597 from high-voltage spikes on the
bus lines, and minimize crosstalk and undershoot of the
bus signals.
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
DEV_ADDR
B7
B6
B5
B4
B3
B2
B1
B0
WRITE ADDRESS
(HEX)
READ ADDRESS
(HEX)
GND
1001010
R/
W
94h
95h
VVID
1001011
R/
W
96h
97h
SCL
1001100
R/
W
98h
99h
SDA
1001101
R/
W
9Ah
9Bh
Table 3. Slave Address
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START CONDITION
START
CONDITION
tHD, STA
tSU, STA
tHD, STA
tSP
tBUF
tSU, STO
tLOW
tSU, DAT
tHD, DAT
tHIGH
tR
tF
Figure 4. I2C Serial-Interface Timing Diagram
SMBus is a trademark of Intel Corp.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9602EUG+T | IC COMPARATOR HS 24-TSSOP |
| MAX9646EUK+T | IC COMPARATOR W/REF SOT23-5 |
| MAX9648AXK+T | IC COMPARATOR GP SGL SC70-5 |
| MAX964EEE+T | IC COMPARATOR BTR 16-QSOP |
| MAX964EEE | IC COMP BEYOND-RAILS QUAD 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9597CTI+ | 功能描述:視頻 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MAX9597CTI+T | 功能描述:視頻 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MAX9597EVKIT+ | 功能描述:視頻 IC 開發工具 MAX9597 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Boards 類型:YPbPr to RGBHV Converters 工具用于評估:LMH1251 工作電源電壓:5 V |
| MAX9598CTL+ | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598CTL+T | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。