- 您現在的位置：買賣IC網 > PDF目錄3319 > MAX9626ATC+ (Maxim Integrated Products)IC DIFF AMP/DRIVER LN 12TQFN PDF資料下載
參數資料
| 型號： | MAX9626ATC+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/20頁 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/DRIVER LN 12TQFN |
| 標準包裝： | 100 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 輸出類型： | 差分 |
| 轉換速率： | 6500 V/µs |
| -3db帶寬： | 700MHz |
| 電流 - 輸入偏壓： | 1µA |
| 電壓 - 輸入偏移： | 2000µV |
| 電流 - 電源： | 59mA |
| 電流 - 輸出 / 通道： | 100mA |
| 電壓 - 電源，單路/雙路(±)： | 2.85 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
MAX9626/MAX9627/MAX9628
Low-Noise, Low-Distortion,
1.35GHz Fully Differential Amplifiers
17
Input Voltage Noise
The input referred voltage noise specification reported
in the Electrical Characteristics table includes both the
noise contribution of the amplifier and the contribution of
all the internal resistive elements. Because such resistive
elements change depending on the gain selection as
per Table 1, the input voltage noise specification differs
according to the gain options.
Setting the Output Common-Mode Voltage
The ICs feature an input, VOCM, that sets the differential
output common-mode voltage. Its wide range from 1.1V
to VCC - 1.1V makes the amplifier family compatible with
most of the high-speed pipeline differential input ADCs.
While many of these ADCs accept an input common-
mode around half of their supply voltage, some of them
have input common-mode range shifted toward either
ground or the positive supply.
The ICs can comfortably drive both 3.3V and 5V ADCs
that have common-mode range around half supply.
When powered with VCC of 5V or higher, the ICs can
also drive some of the popular ADCs with common-mode
range higher than 3V.
The high bandwidth of VOCM makes the amplifier's out-
put recover quickly from load transient conditions. Such
conditions may occur when switching the ADC input
capacitor during the track-and-hold phases. The input
capacitor switching may cause a voltage glitch at the
input of the ADC, which incurs a load transient condition
for the driving amplifier.
Power-Supply Decoupling
and Layout Techniques
The ICs are high-speed devices, sensitive to the PCB
environment in which they operate. Realizing their superior
performance requires attention to the details of high-
speed PCB design.
The first requirement is a solid continuous ground plane
on the second PCB layer, preferably with no signal or
power traces. PCB layers 3 and 4 can be power-supply
routing or signal routing, but preferably they should not
be routed together.
For power-supply decoupling with single-supply opera-
tion, place a large capacitor by the VCC supply node
and then place a smaller capacitor as close as possible
to the VCC pin. For 1GHz decoupling, 22pF to 100pF are
good values to use. When used with split supplies, place
relevant capacitors on the VEE supply as well.
Ground vias are critical to provide a ground return path
for high frequency signals and should be placed near
the decoupling capacitors. Place ground vias on the
exposed pad as well, along the edges and near the pins
to shorten the return path and maximize isolation. Vias
should also be placed next to the input and output signal
traces to maximize isolation. Finally, make sure that the
layer 2 ground plane is not severely broken up by signal
vias or power supply vias.
Signal routing should be short and direct to avoid
parasitic effects. For very high-frequency designs, avoid
using right angle connectors since they may introduce
a capacitive discontinuity and ultimately limit the fre-
quency response.
Recommended Pipeline ADCs
The MAX9626/MAX9627/MAX9628 family offers excel-
lent bandwidth and distortion performance that is in line
with the majority of high-speed and 16-bit resolution
pipeline ADCs in the market. In particular, it is recom-
mended in combination with the MAX19586/MAX19588
family of 16-bit and 100Msps pipeline ADCs.
For lower resolution applications, the MAX9626/
MAX9627/MAX9628 family can also drive 10- to 14-bit
ADCs such as the MAX12553/MAX12554/MAX12555,
MAX12527/MAX12528/MAX12529 and MAX19505/
MAX19506/MAX19507 families.
相關PDF資料 |
PDF描述 |
|---|---|
| 51864-6 | CONN RING 16 AWG #6 PIDG |
| 35787 | CONN RING 10-12 AWG #8 PIDG |
| MAX407CSA | IC OPAMP PREC DUAL 1.2UA 8-SOIC |
| MAX407CPA | IC OPAMP PREC DUAL 1.2UA 8-DIP |
| 2-33462-1 | CONN RING TONG 8AWG #5/16 TIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9626ATC+ | 功能描述:差分放大器 Low-Noise/Distortion Differential Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| MAX9626ATC+T | 功能描述:差分放大器 1.35GHz Fully Diff Amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| MAX9626ETC+ | 功能描述:差分放大器 Low-Noise/Distortion Differential Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| MAX9626EVKIT+ | 功能描述:放大器 IC 開發工具 Low-Noise Low-Distortion Differential-Input Differential-Output Fixed-Gain Amplifiers RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9627ATC+ | 功能描述:差分放大器 Low-Noise/Distortion Differential Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。